Appendix a, Default Settings | Omnitron Systems Technology RS-232

Appendix A

DEFAULT SETTINGS

The Omni reader is shipped from the factory with the following bar code default settings already programmed:

Terminal Selection
Type	RS-232 (Serial)
General Selection
Beep Volume	High
Interblock Delay	0 milliseconds
Code ID	Off
Scan Veriﬁcation	Off
Automatic Veriﬁcation	01
Bar Code Message Formatting
Terminator Character	CRLF
Preamble	None
Postamble	None
Magentic Stripe Message Formatting
Terminator Character	CRLF
Preamble	None
Postamble	None
RS-232 Port Settings
Baud Rate	9600
Data Bits	8
Parity	None
Handshaking	X-On/X-Off
Stop Bit(s)	1
X-On	DC1 (\11)
X-Off	DC3 (\13)

48

Image 54

Omnitron Systems Technology RS-232 user manual Appendix a, Default Settings, Crlf

Contents

Omnitm Page Limited Warranty Agency ApprovedPage Table of Contents Page Section IntroductionDescription Installation Host Connections Bar Code Input ConfigurationConfiguration Setup Procedure Magnetic Stripe Input Example Default Settings Serial Interface Parameters Group E Baud Rate Parity General Selections Group B Stop Bit Beep Volume Code/Track IDScan Verification Code ID Definition Group Enter one character for the new ID Bar Code Message Formatting Selections Group C Bar Code Terminator Character Bar Code Preamble Bar Code Postamble Magnetic Stripe Formatting Selections Group D Magnetic Stripe Terminator Character Magnetic Stripe Preamble Magnetic Stripe Postamble Bar Code Selections Industrial Bar Codes Group FMinimum and Maximum Length Options Code 39 Settings Enable/Disable CodeFull Ascii Check Digit Interleaved 2 of 5 SettingsEnable/Disable Interleaved 2 Send Start/Stop Characters Febraban Conversion Fixed Length Industrial 2 of 5 Settings Enable/Disable Industrial 2 Code 128 Setting Codabar Settings Enable/Disable Codabar Enable/Disable MSI/Plessey MSI/Plessey SettingsTelepen Setting Enable/Disable Telepen UPC Settings Enable/Disable UPC-ARetail Bar Codes Group G Send Check Digit Enable/Disable UPC-ESend Number System Digit UPC-E Expansion Addendum Required Read Two-Digit AddendumRead Five-Digit Addendum Add Separator Space Enable/Disable EAN-8 EAN SettingsEnable/Disable EAN-13 Send Induced Country Code Character Read Five-Digit Addendum Do Not Read Five-Digit Addendum Magnetic Stripe Selections Group H Track SelectionSend Start/Stop Sentinel Track Separator Reviewing Configuration SettingsTrack Two Send Accout Number Only H4ENTERSELECTED Characterenter MSI Data Editing Data Fields Data Editing Formulas Formula Sequence Code Idlengthmatchdivideaddsend Using the Data Editing Functions Track 1 %CABREADOE$JANE$R$310 S Jefferson ST? Data Editing Commands Data Editing On/OffUnmatched Input Send/Do Not Send Select Code IDs Set LengthJDENTER0ENTER6ENTER1ENTER2ENTER JEENTER0ENTER8ENTERAENTERBENTER Centerdentereenter Match StringCreate a Data Field JFENTER0ENTER7ENTER Search for a Data String Add a Data FieldJgenteraenterbentercenter Dentereenter Delete One Formula Time DelaySet the Sequence in which Data Fields are Sent Jkenteraentercenterbenter Exit Data Editing Mode Reset Data Editing GroupReview Configurations Omni Data Flow Symbology Code Examples Enter 7ENTER Send BD DLY 09 AD DLYJDENTER0ENTER7ENTER0 JEENTER0ENTER7ENTER MSR Track 1 data Operating Procedure Operation Troubleshooting General Procedures Serial Interface Problems Scanning Configurations Default Settings Appendix aCrlf Industrial Bar Codes Retail Barcodes UPC-A, -EUPC-A UPC-E EAN-8 Appendix B Magnetic Stripe Format Appendix C Magnetic Stripe Standard Data Formats California Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Appendix D Full Ascii Table Ascii Connector PIN-OUTS Appendix ERS-232 Port, Standard DB-9P Installing the Drivers Appendix FUSB/RS-232 Interface Page UE Anyway Checking the Installation and Modifying the COM Port Number Telling Whether the Installed Device is Type a or Type BTroubleshooting Updating the Driver Date Driver Removing the Driver Versal Serial BUS Controllers ID Tech