Retail Barcodes, Upc-A, -E | Omnitron Systems Technology RS-232

Retail Barcodes
UPC-A, -E	Enabled, Enabled
Send Number System Digit	Yes
Send Check Digit	Yes
Expand UPC-E	No
Read 2, 5 Digit Addendum	No, No
Addendum required	Yes
Add Addendum Separator	Yes
Send UPC-A as EAN-13	No
EAN-13, -8	Enabled, Enabled
Send Induced Country Code Digit	Yes
Send Check Digit	Yes
Read 2, 5 Digit Addendum	No, No
Addendum Required	Yes
Add Addendum Separator	Yes
Code ID
UPC-A	a
UPC-E	b
EAN-8	c
EAN-13	d
Code 39	e
Interleaved 2 of 5	f
Industrial 2 of 5	g
Code 128	h
MSI/Plessey	i
Codabar	j
MSR Track 1	k
MSR Track 2	l
MSR Track 3	m
Telepen	n
Data Editing
Edit On/Off	Off
Unmatched Input	Send

50

Image 56

Omnitron Systems Technology RS-232 user manual Retail Barcodes, Upc-A, -E, UPC-A UPC-E EAN-8

Contents

Omnitm Page Limited Warranty Agency ApprovedPage Table of Contents Page Description SectionIntroduction Installation Host Connections Configuration Configuration Setup ProcedureBar Code Input Magnetic Stripe Input Example Default Settings Serial Interface Parameters Group E Baud Rate Parity General Selections Group B Stop Bit Scan Verification Beep VolumeCode/Track ID Code ID Definition Group Enter one character for the new ID Bar Code Message Formatting Selections Group C Bar Code Terminator Character Bar Code Preamble Bar Code Postamble Magnetic Stripe Formatting Selections Group D Magnetic Stripe Terminator Character Magnetic Stripe Preamble Magnetic Stripe Postamble Minimum and Maximum Length Options Bar Code SelectionsIndustrial Bar Codes Group F Full Ascii Code 39 SettingsEnable/Disable Code Interleaved 2 of 5 Settings Enable/Disable Interleaved 2Check Digit Send Start/Stop Characters Febraban Conversion Fixed Length Industrial 2 of 5 Settings Enable/Disable Industrial 2 Code 128 Setting Codabar Settings Enable/Disable Codabar MSI/Plessey Settings Telepen SettingEnable/Disable MSI/Plessey Enable/Disable Telepen Retail Bar Codes Group G UPC SettingsEnable/Disable UPC-A Enable/Disable UPC-E Send Number System DigitSend Check Digit UPC-E Expansion Read Two-Digit Addendum Read Five-Digit AddendumAddendum Required Add Separator Space EAN Settings Enable/Disable EAN-13Enable/Disable EAN-8 Send Induced Country Code Character Read Five-Digit Addendum Do Not Read Five-Digit Addendum Send Start/Stop Sentinel Magnetic Stripe Selections Group HTrack Selection Reviewing Configuration Settings Track Two Send Accout Number OnlyTrack Separator H4ENTERSELECTED Characterenter MSI Data Editing Data Fields Data Editing Formulas Formula Sequence Code Idlengthmatchdivideaddsend Using the Data Editing Functions Track 1 %CABREADOE$JANE$R$310 S Jefferson ST? Unmatched Input Send/Do Not Send Data Editing CommandsData Editing On/Off JDENTER0ENTER6ENTER1ENTER2ENTER Select Code IDsSet Length Match String Create a Data FieldJEENTER0ENTER8ENTERAENTERBENTER Centerdentereenter JFENTER0ENTER7ENTER Jgenteraenterbentercenter Dentereenter Search for a Data StringAdd a Data Field Time Delay Set the Sequence in which Data Fields are SentDelete One Formula Jkenteraentercenterbenter Reset Data Editing Group Review ConfigurationsExit Data Editing Mode Omni Data Flow Symbology Code Examples Send BD DLY 09 AD DLY JDENTER0ENTER7ENTER0Enter 7ENTER JEENTER0ENTER7ENTER MSR Track 1 data Operating Procedure Operation Troubleshooting General Procedures Serial Interface Problems Scanning Configurations Crlf Default SettingsAppendix a Industrial Bar Codes UPC-A UPC-E EAN-8 Retail BarcodesUPC-A, -E Appendix B Magnetic Stripe Format Appendix C Magnetic Stripe Standard Data Formats California Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Appendix D Full Ascii Table Ascii RS-232 Port, Standard DB-9P Connector PIN-OUTSAppendix E USB/RS-232 Interface Installing the DriversAppendix F Page UE Anyway Troubleshooting Checking the Installation and Modifying the COM Port NumberTelling Whether the Installed Device is Type a or Type B Updating the Driver Date Driver Removing the Driver Versal Serial BUS Controllers ID Tech