Removing the Driver | Omnitron Systems Technology RS-232 manual

Removing the Driver

1.With the reader plugged in, go to START/CONTROL PANEL/SYSTEM/ HARDWARE/DEVICE MANAGER/PORTS (COM & LPT) and/or UNI-

VERSAL SERIAL BUS CONTROLLERS.

2.Locate any items like “Unknown USB Device” or “(ID TECH) USB Serial Converter” or “(ID TECH)USB Serial Port” marked with a yellow “!”

3.Right-click on the item and select the UNINSTALL option to remove the driver.

4.The CONFIRM DEVICE REMOVAL window will open. Click OK.

5.After the driver has been removed, unplug and then plug the reader in again.

6.A “Found new hardware wizard” window should appear on the screen. Install the driver again.

64

Image 70

Omnitron Systems Technology RS-232 user manual Removing the Driver, Versal Serial BUS Controllers

Contents

Omnitm Page Limited Warranty Agency ApprovedPage Table of Contents Page Introduction SectionDescription Installation Host Connections Bar Code Input ConfigurationConfiguration Setup Procedure Magnetic Stripe Input Example Default Settings Serial Interface Parameters Group E Baud Rate Parity General Selections Group B Stop Bit Code/Track ID Beep VolumeScan Verification Code ID Definition Group Enter one character for the new ID Bar Code Message Formatting Selections Group C Bar Code Terminator Character Bar Code Preamble Bar Code Postamble Magnetic Stripe Formatting Selections Group D Magnetic Stripe Terminator Character Magnetic Stripe Preamble Magnetic Stripe Postamble Industrial Bar Codes Group F Bar Code SelectionsMinimum and Maximum Length Options Enable/Disable Code Code 39 SettingsFull Ascii Check Digit Interleaved 2 of 5 SettingsEnable/Disable Interleaved 2 Send Start/Stop Characters Febraban Conversion Fixed Length Industrial 2 of 5 Settings Enable/Disable Industrial 2 Code 128 Setting Codabar Settings Enable/Disable Codabar Enable/Disable MSI/Plessey MSI/Plessey SettingsTelepen Setting Enable/Disable Telepen Enable/Disable UPC-A UPC SettingsRetail Bar Codes Group G Send Check Digit Enable/Disable UPC-ESend Number System Digit UPC-E Expansion Addendum Required Read Two-Digit AddendumRead Five-Digit Addendum Add Separator Space Enable/Disable EAN-8 EAN SettingsEnable/Disable EAN-13 Send Induced Country Code Character Read Five-Digit Addendum Do Not Read Five-Digit Addendum Track Selection Magnetic Stripe Selections Group HSend Start/Stop Sentinel Track Separator Reviewing Configuration SettingsTrack Two Send Accout Number Only H4ENTERSELECTED Characterenter MSI Data Editing Data Fields Data Editing Formulas Formula Sequence Code Idlengthmatchdivideaddsend Using the Data Editing Functions Track 1 %CABREADOE$JANE$R$310 S Jefferson ST? Data Editing On/Off Data Editing CommandsUnmatched Input Send/Do Not Send Set Length Select Code IDsJDENTER0ENTER6ENTER1ENTER2ENTER JEENTER0ENTER8ENTERAENTERBENTER Centerdentereenter Match StringCreate a Data Field JFENTER0ENTER7ENTER Add a Data Field Search for a Data StringJgenteraenterbentercenter Dentereenter Delete One Formula Time DelaySet the Sequence in which Data Fields are Sent Jkenteraentercenterbenter Exit Data Editing Mode Reset Data Editing GroupReview Configurations Omni Data Flow Symbology Code Examples Enter 7ENTER Send BD DLY 09 AD DLYJDENTER0ENTER7ENTER0 JEENTER0ENTER7ENTER MSR Track 1 data Operating Procedure Operation Troubleshooting General Procedures Serial Interface Problems Scanning Configurations Appendix a Default SettingsCrlf Industrial Bar Codes UPC-A, -E Retail BarcodesUPC-A UPC-E EAN-8 Appendix B Magnetic Stripe Format Appendix C Magnetic Stripe Standard Data Formats California Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Appendix D Full Ascii Table Ascii Appendix E Connector PIN-OUTSRS-232 Port, Standard DB-9P Appendix F Installing the DriversUSB/RS-232 Interface Page UE Anyway Telling Whether the Installed Device is Type a or Type B Checking the Installation and Modifying the COM Port NumberTroubleshooting Updating the Driver Date Driver Removing the Driver Versal Serial BUS Controllers ID Tech