Appendix E, Connector PIN-OUTS | Omnitron Systems Technology RS-232

Appendix E

CONNECTOR PIN-OUTS

RS-232 Port, Standard DB-9P
Connector Pin	Direction	Signal (TTL level)
1		No Connection
3	To Omni	Receive Data (RxD)
2	To Host	Transmit Data (TxD)
5		Signal Ground
8	To Host	Request To Send (RTS)
7	To Omni	Clear To Send (CTS)
9		No Connection

58

Image 64

Omnitron Systems Technology user manual Appendix E, Connector PIN-OUTS, RS-232 Port, Standard DB-9P

Contents

Omnitm Page Limited Warranty Agency ApprovedPage Table of Contents Page Introduction SectionDescription Installation Host Connections Configuration Configuration Setup ProcedureBar Code Input Magnetic Stripe Input Example Default Settings Serial Interface Parameters Group E Baud Rate Parity General Selections Group B Stop Bit Code/Track ID Beep VolumeScan Verification Code ID Definition Group Enter one character for the new ID Bar Code Message Formatting Selections Group C Bar Code Terminator Character Bar Code Preamble Bar Code Postamble Magnetic Stripe Formatting Selections Group D Magnetic Stripe Terminator Character Magnetic Stripe Preamble Magnetic Stripe Postamble Industrial Bar Codes Group F Bar Code SelectionsMinimum and Maximum Length Options Enable/Disable Code Code 39 SettingsFull Ascii Interleaved 2 of 5 Settings Enable/Disable Interleaved 2Check Digit Send Start/Stop Characters Febraban Conversion Fixed Length Industrial 2 of 5 Settings Enable/Disable Industrial 2 Code 128 Setting Codabar Settings Enable/Disable Codabar MSI/Plessey Settings Telepen SettingEnable/Disable MSI/Plessey Enable/Disable Telepen Enable/Disable UPC-A UPC SettingsRetail Bar Codes Group G Enable/Disable UPC-E Send Number System DigitSend Check Digit UPC-E Expansion Read Two-Digit Addendum Read Five-Digit AddendumAddendum Required Add Separator Space EAN Settings Enable/Disable EAN-13Enable/Disable EAN-8 Send Induced Country Code Character Read Five-Digit Addendum Do Not Read Five-Digit Addendum Track Selection Magnetic Stripe Selections Group HSend Start/Stop Sentinel Reviewing Configuration Settings Track Two Send Accout Number OnlyTrack Separator H4ENTERSELECTED Characterenter MSI Data Editing Data Fields Data Editing Formulas Formula Sequence Code Idlengthmatchdivideaddsend Using the Data Editing Functions Track 1 %CABREADOE$JANE$R$310 S Jefferson ST? Data Editing On/Off Data Editing CommandsUnmatched Input Send/Do Not Send Set Length Select Code IDsJDENTER0ENTER6ENTER1ENTER2ENTER Match String Create a Data FieldJEENTER0ENTER8ENTERAENTERBENTER Centerdentereenter JFENTER0ENTER7ENTER Add a Data Field Search for a Data StringJgenteraenterbentercenter Dentereenter Time Delay Set the Sequence in which Data Fields are SentDelete One Formula Jkenteraentercenterbenter Reset Data Editing Group Review ConfigurationsExit Data Editing Mode Omni Data Flow Symbology Code Examples Send BD DLY 09 AD DLY JDENTER0ENTER7ENTER0Enter 7ENTER JEENTER0ENTER7ENTER MSR Track 1 data Operating Procedure Operation Troubleshooting General Procedures Serial Interface Problems Scanning Configurations Appendix a Default SettingsCrlf Industrial Bar Codes UPC-A, -E Retail BarcodesUPC-A UPC-E EAN-8 Appendix B Magnetic Stripe Format Appendix C Magnetic Stripe Standard Data Formats California Driver’s License Format Track LRE ID Aamva Driver’s License Format Track Appendix D Full Ascii Table Ascii Appendix E Connector PIN-OUTSRS-232 Port, Standard DB-9P Appendix F Installing the DriversUSB/RS-232 Interface Page UE Anyway Telling Whether the Installed Device is Type a or Type B Checking the Installation and Modifying the COM Port NumberTroubleshooting Updating the Driver Date Driver Removing the Driver Versal Serial BUS Controllers ID Tech