Panasonic PT-D7600U operating instructions Appendix, Compatible RGB/YPBPR Signals

Appendix

<Compatible RGB/YPBPR Signals>

The following table specifies the types of RGB/ YPBPR signals compatible with the projector.

RGB signals can also be input within the range of fH=15 kHz–100 kHz, fV=24 Hz–120 Hz, dot clock=20 MHz–162 MHz.

Display mode				Applicable input signal data
	Number of displayed dots			Horizontal scanning frequency (kHz)	Vertical scanning frequency (Hz)
VGA400	640	x	400	24.8	56.4
	640	x	400	31.5	70.1
	640	x	480	31.5	59.9
	640	x	480	35.0	66.7
VGA480	640	x	480	37.9	72.8
	640	x	480	37.5	75.0
	640	x	480	43.3	85.0
	800	x	600	32.1	51.0
	800	x	600	35.2	56.3
SVGA	800	x	600	37.9	60.3
	800	x	600	48.1	72.1
	800	x	600	46.9	75.0
	800	x	600	53.7	85.1
	1 024	x	768	48.4	60.0
	1 024	x	768	56.5	70.1
	1 024	x	768	60.0	75.0
XGA	1 024	x	768	65.5	81.6
	1 024	x	768	68.7	85.0
	1 024	x	768i	35.5	86.8
	1 024	x	768	80.7	100.8
	1 024	x	768	94.0	120.0
	1 152	x	864	63.9	70.0
	1 152	x	864	67.5	75.0
MXGA	1 152	x	864	77.1	85.0
	1 120	x	750	50.1	60.1
	1 120	x	750i	32.6	80.0
	1 280	x	1 024	52.4	50.0
	1 280	x	1 024	64.0	60.0
	1 280	x	1 024	72.4	66.3
SXGA	1 280	x	1 024	78.2	71.7
	1 280	x	1 024	80.0	75.0
	1 280	x	1 024	91.2	85.0
	1 280	x	1 024i	46.2	86.0
	1 280	x	1 024i	47.6	88.9
UXGA	1 600	x	1 200	75.0	60.0
MAC16	832	x	624	49.7	74.6
MAC21	1 152	x	870	68.6	75.0
HDTV	1 920	x	1 035i	33.8	60.0
720p	1 280	x	720	45.0	60.0
NTSC	768	x	480i	15.7	59.9
PAL	768	x	576i	15.6	50.0
480p	720	x	483	31.5	59.9

Note • The number of displayed dots of PT-D7600U is 1280 x 1024. Those combinations listed in the above table that exceed these limits will be converted into 1280 x 1024 for display.

•The number of displayed dots of PT-D7500U is 1024 x 768. Those combinations listed in the above table that exceed these limits will be converted into 1024 x 768 for display.

•Character “i” that follows the number of displayed dots stands for interlace signal.

•Flicker (line flicker) will be caused in images if interlace signals are connected.

102