Basic operations on menu screen
Press the “MENU” button.
The MAIN MENU appears on the screen.
MAIN MENU
PICTURE
POSITION
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
:MENU SELECT
ENTER:SUB MENU
Select the desired item with the 
or 
button.
Selected items are displayed in blue.
MAIN MENU
PICTURE
POSITION
LANGUAGE
OPTION
TEST PATTERN
SIGNAL LIST
:MENU SELECT
ENTER:SUB MENU
Press the “ENTER” button to establish your selection.
The submenu for the selected option will now open. (Example: PICTURE Menu)
PICTURE
PICTURE MODE | STANDARD | ||||
COLOR | 50 |
|
|
|
|
|
|
|
| ||
|
|
|
| ||
TINT | 30 |
|
|
|
|
|
|
|
| ||
|
|
|
| ||
COLOR TEMP. | STANDARD | ||||
GAMMA | STANDARD | ||||
CONTRAST | 32 |
|
|
|
|
BRIGHT | 32 |
|
|
|
|
|
|
|
| ||
|
|
|
| ||
SHARPNESS | 6 |
|
|
|
|
NOISE REDUCTION | 2 |
|
|
|
|
AI CONTROL | OFF | ||||
:MENU SELECT 
:ADJUST
Highlight the desired adjustment item with the 
or 
button, then change or adjust the parameter value with the 
or 
buttons.
For the items such as “COLOR”, “TINT”, “CONTRAST” and “BRIGHT”, an individual adjustment screen with an individual bar graph as shown below is displayed by pressing the ENTER button.
CONTRAST32
•If no button is operated for approx. 5 seconds while the individual adjustment screen is displayed, the screen will return to the previous page.
Returning to the previous screen
•When the “MENU” is on the screen, pressing the “MENU” button returns to the previous page.
•When the MAIN MENU is on the screen, pressing the “MENU” button clears all menus from the screen.
Menu items shown in gray characters
•Some menu items may not be valid for certain signal formats applied to the projector.
The menu items that cannot be adjusted or used are shown in gray characters, and they cannot be selected.
Menu items setting
The bottom prompt line differs on each menu depending on the selected menu option:
•A prompt “ 
CHANGE” appears when changing the setting.
• A prompt “ 
ADJUST” appears for a separate bar graph.
•When 
and 
buttons are displayed above or under the items in the “PICTURE” or “OPTION” screen, they indicate that there are more adjustment (items).
Resetting to the factory default
STD (standard) button is used to reset all of the projector adjustment values to the default levels which were set at the time of shipment from the factory. It is pressed after the respective adjustment mode screen has been displayed.
•When the Menu screen is displayed
A“STD” indicator appears on the upper right corner of the menu.
PICTURE |
|
|
|
| STD | |
| PICTURE MODE | STANDARD | ||||
| COLOR | 32 |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| ||
| TINT | 32 |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| ||
| COLOR TEMP. | STANDARD | ||||
| GAMMA | STANDARD | ||||
| CONTRAST | 32 |
|
|
|
|
| BRIGHT | 32 |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
| ||
| SHARPNESS | 6 |
|
|
|
|
| NOISE REDUCTION | 2 |
|
|
|
|
| AI CONTROL | OFF | ||||
:MENU SELECT 
:ADJUST
50