Nortel Networks 600r manual Global CallPilot Support for Anti-Virus

Page 22

22Chapter 3 Preparing for installation

Step

Description

Check

2

Unpack the server and ensure you have all the items you

__

 

need (see "Unpacking the 600r server" (page 23)).

 

 

Complete the following checklists that are provided in the

 

 

Installation and Configuration Task List (NN44200-306):

 

 

• CallPilot software media and documentation checklist

 

 

• CallPilot server hardware checklist

 

 

 

 

3

Remove the top cover and inspect the interior (see

__

 

"Inspecting the interior of server" (page 24)).

 

 

 

 

4

Replace the top cover.

__

 

 

 

5

Place the 600r server in the chosen location and connect

__

 

the SCSI terminator (see "Installing the server" (page 27)).

 

 

 

 

6

Connect the 600r server and devices as follows:

__

 

• Connect the monitor, keyboard, and mouse (see "To

__

 

connect the mouse, keyboard, and monitor to the

 

 

server" (page 29)).

 

 

• Connect the modem (see "To connect the modem to

__

 

the server" (page 30)).

 

 

• Connect the 600r server to the ELAN Ethernet switch

__

 

or hub (see "To connect the server to the ELAN subnet

 

 

(Meridian 1 or CS 1000 only)" (page 32)).

 

 

Note: If you are connecting the optional Nortel server

 

 

subnet, do not connect until you ensure that CallPilot has

 

 

the latest antivirus software. Do not install third-party

 

 

antivirus software unless approved by Nortel. For

 

 

information about the antivirus software packages that

 

 

are approved by Nortel for CallPilot, see Product Bulletin

 

 

P-2007-0101-Global : CallPilot Support for Anti-Virus

 

 

Applications. Also, ensure your CallPilot application

 

 

resides behind your network firewall.

 

 

• Connect the 600r server to the CLAN Ethernet switch

__

 

or hub (optional); (see "Connecting the server to the

 

 

Nortel server subnet (optional)" (page 33)).

 

 

• Install the software feature dongle (see "Installing the

__

 

Nortel software feature dongle" (page 34)).

 

 

• Connect the power cords for all peripheral devices, and

__

 

then power them up (see "Connecting the server to

 

 

power" (page 40) for power requirements).

 

 

 

 

7

Start the 600r server (see "What is next?" (page 43)).

__

Nortel CallPilot

600r Server Hardware Installation

NN44200-307 01.03 Standard

5.014 May 2008

Copyright © 2007-2008, Nortel Networks

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 600r Server Hardware Installation Trademarks Japan Denan statement Information for JapanJapan Vcci statement Page May Publication HistoryMarch Publication History Contents Contents Getting help over the phone from a Nortel Solutions Center Chapter How to get helpGetting help from the Nortel Web site Getting help through a Nortel distributor or reseller Conventions for Warnings Chapter 600r server descriptionThis chapter Server features Server dimensionsEnvironmental specifications Front panel featuresSpecification Environmental conditionPower button NMI button not used Reset button ID button Front panelLabel Description Rear panel controls and featuresRear panel Label Description PCI riser assembly PCI riser assemblyNetwork connectivity Sample network setup with Meridian Sample network setup MeridianSample network setup Communication Server Sample network setup with Communication ServerSwitch connectivity LAN connectivity Network requirements Remote access connectivity Supported peripheral devices Supported peripheral devices Device DescriptionReference documents Installation checklist Chapter Preparing for installationInstallation overview IntroductionGlobal CallPilot Support for Anti-Virus Unpacking the 600r server What is next?To unpack the equipment To remove the server cover Inspecting the interior of serverTo replace the server cover Inspecting the interior of server Preparing for installation Chapter Installing the server and peripheral devices Installing the serverTo install the server Connecting peripherals to the serverRear panel connectors Rear panel Rear panel connectors Label Description To connect the mouse, keyboard, and monitor to the serverTo connect the modem to the server To connect the external Scsi tape driveScsi tape drive with terminator Connecting the server to the Elan subnet Media Access Control address Connecting the server to the Nortel server subnet optionalIf the server Then Installing the Nortel software feature dongle To connect the server to the Nortel server subnetTo install the software feature dongle Dongle plugged in to serverDongle without feature key Installing the software feature keyContinue with Connecting the server to power Installing the server and peripheral devices Locating the power supply modules Chapter Connecting the server to powerSafety precautions Safety informationRack power and grounding Connecting the server to powerAbout the power supply module Before you beginConnecting the server to power To connect the 600r server to power Example setup of 600r with peripheralsWhat is next? Connecting the server to power Chapter EMC emission level protection for the 600r server Ferrite cores secured to an external cable Symbols/Numerics IndexIndex Index Index Page 600r Server Hardware Installation
Top Page Image Contents