Nortel Networks 600r manual Installing the Nortel software feature dongle

Page 34

34Chapter 4 Installing the server and peripheral devices

power switch. Two MAC addresses are shown on the label. The CLAN MAC address is the top MAC address, labeled MAC1, while the ELAN MAC address is labelled MAC2.

To connect the server to the Nortel server subnet

Step Action

1On the back of the server, locate the CLAN connector.

Note: The CLAN connector is labeled 1 on the rear panel of the 600r. For the connector location, see the diagram on Figure 7 "Rear panel" (page 29), Label I.

2Connect an RJ-45 network cable from the CLAN Ethernet switch or hub to the CLAN connector.

Note: When connecting the optional Nortel server subnet, do not connect to the network until you ensure that CallPilot has the latest antivirus software. Do not install third-party antivirus software unless approved by Nortel. For information about the antivirus software packages that are approved by Nortel for CallPilot, see Product Bulletin P-2007-0101-Global : CallPilot Support for Anti-Virus Applications. Also, ensure your CallPilot application resides behind your network ﬁrewall.

—End—

What is next?

Continue with "Installing the Nortel software feature dongle" (page 34).

Installing the Nortel software feature dongle

The software feature key is a security device that stores the unique serial number of the server. The feature key is embedded in the Nortel software feature dongle that plugs in to a USB port on the rear panel.

The following diagram shows the dongle plugged in to the back panel of the server:

Nortel CallPilot

600r Server Hardware Installation

NN44200-307 01.03 Standard

5.014 May 2008

Copyright © 2007-2008, Nortel Networks

Image 34

Contents 600r Server Hardware Installation Trademarks Japan Denan statement Information for JapanJapan Vcci statement Page May Publication HistoryMarch Publication History Contents Contents Getting help over the phone from a Nortel Solutions Center Chapter How to get helpGetting help from the Nortel Web site Getting help through a Nortel distributor or reseller Conventions for Warnings Chapter 600r server descriptionThis chapter Server features Server dimensionsEnvironmental speciﬁcations Front panel featuresSpecification Environmental conditionPower button NMI button not used Reset button ID button Front panelLabel Description Rear panel controls and featuresRear panel Label Description PCI riser assembly PCI riser assemblyNetwork connectivity Sample network setup with Meridian Sample network setup MeridianSample network setup Communication Server Sample network setup with Communication ServerSwitch connectivity LAN connectivityNetwork requirements Remote access connectivitySupported peripheral devices Supported peripheral devices Device DescriptionReference documents Installation checklist Chapter Preparing for installationInstallation overview IntroductionGlobal CallPilot Support for Anti-Virus Unpacking the 600r server What is next?To unpack the equipment To remove the server cover Inspecting the interior of serverTo replace the server cover Inspecting the interior of server Preparing for installation Chapter Installing the server and peripheral devices Installing the serverTo install the server Connecting peripherals to the serverRear panel connectors Rear panel Rear panel connectors Label Description To connect the mouse, keyboard, and monitor to the serverTo connect the modem to the server To connect the external Scsi tape drive Scsi tape drive with terminator Connecting the server to the Elan subnet Media Access Control address Connecting the server to the Nortel server subnet optionalIf the server Then Installing the Nortel software feature dongle To connect the server to the Nortel server subnetTo install the software feature dongle Dongle plugged in to serverDongle without feature key Installing the software feature keyContinue with Connecting the server to power Installing the server and peripheral devices Locating the power supply modules Chapter Connecting the server to powerSafety precautions Safety informationRack power and grounding Connecting the server to powerAbout the power supply module Before you beginConnecting the server to power To connect the 600r server to power Example setup of 600r with peripheralsWhat is next? Connecting the server to power Chapter EMC emission level protection for the 600r server Ferrite cores secured to an external cable Symbols/Numerics IndexIndex Index Index Page 600r Server Hardware Installation