Nortel Networks 600r manual Connecting the server to the Elan subnet, What is next?

Page 32

32Chapter 4 Installing the server and peripheral devices

4Install the SCSI tape drive terminator to the back of the SCSI tape drive, as shown in Figure 8, under the label Tape drive terminator.

Note: Nortel does not recommend connecting older SCSI protocol terminators, as this can affect server performance.

5Plug the tape drive into the same single point ground and A/C power as the rest of the system.

6Power on the tape drive.

Note: Your 600r comes with the tape drive drivers preinstalled. During the loading of Windows, the system automatically detects the tape drive and loads the drivers that are necessary to operate the tape drive. When system startup is complete, the tape drive is ready for use.

—End—

What is next?

Connect the server to the ELAN subnet and Nortel server subnet (if applicable).

Note: Before you connect to the network, ensure that CallPilot has the latest antivirus software. Do not install third-party antivirus software unless approved by Nortel. For information about the antivirus software packages that are approved by Nortel for CallPilot, see Product Bulletin P-2007-0101-Global : CallPilot Support for Anti-Virus Applications. Also, ensure your CallPilot application resides behind your network firewall.

Connecting the server to the ELAN subnet

Connect the CallPilot server to the Meridian 1 switch or CS 1000 system using the ELAN subnet.

ATTENTION

For important considerations about using the ELAN subnet in your network, see the Planning and Engineering Guide (NN44200-200).

To connect the server to the ELAN subnet (Meridian 1 or CS 1000 only)

Step Action

1On the back of the server, locate the ELAN Ethernet connector.

Nortel CallPilot

600r Server Hardware Installation

NN44200-307 01.03 Standard

5.014 May 2008

Copyright © 2007-2008, Nortel Networks

Image 32
Contents 600r Server Hardware Installation Trademarks Japan Vcci statement Information for JapanJapan Denan statement Page March Publication HistoryMay Publication History Contents Contents Getting help from the Nortel Web site Chapter How to get helpGetting help over the phone from a Nortel Solutions Center Getting help through a Nortel distributor or reseller This chapter Chapter 600r server descriptionConventions for Warnings Server features Server dimensionsFront panel features SpecificationEnvironmental specifications Environmental conditionPower button NMI button not used Reset button ID button Front panelRear panel Label Description Rear panel controls and featuresLabel Description Network connectivity PCI riser assemblyPCI riser assembly Sample network setup Meridian Sample network setup Communication ServerSample network setup with Meridian Sample network setup with Communication ServerSwitch connectivity LAN connectivityRemote access connectivity Supported peripheral devicesNetwork requirements Supported peripheral devices Device DescriptionReference documents Chapter Preparing for installation Installation overviewInstallation checklist IntroductionGlobal CallPilot Support for Anti-Virus To unpack the equipment What is next?Unpacking the 600r server To replace the server cover Inspecting the interior of serverTo remove the server cover Inspecting the interior of server Preparing for installation Chapter Installing the server and peripheral devices Installing the serverRear panel connectors Connecting peripherals to the serverTo install the server Rear panel Rear panel connectors Label Description To connect the mouse, keyboard, and monitor to the serverTo connect the modem to the server To connect the external Scsi tape driveScsi tape drive with terminator Connecting the server to the Elan subnet If the server Then Connecting the server to the Nortel server subnet optionalMedia Access Control address Installing the Nortel software feature dongle To connect the server to the Nortel server subnetTo install the software feature dongle Dongle plugged in to serverDongle without feature key Installing the software feature keyContinue with Connecting the server to power Installing the server and peripheral devices Chapter Connecting the server to power Safety precautionsLocating the power supply modules Safety informationConnecting the server to power About the power supply moduleRack power and grounding Before you beginConnecting the server to power To connect the 600r server to power Example setup of 600r with peripheralsWhat is next? Connecting the server to power Chapter EMC emission level protection for the 600r server Ferrite cores secured to an external cable Symbols/Numerics IndexIndex Index Index Page 600r Server Hardware Installation