Nortel Networks 600r To connect the modem to the server, To connect the external Scsi tape drive

Page 30

30Chapter 4 Installing the server and peripheral devices

To connect the modem to the server

You require a modem to support remote dial-up access to the CallPilot server. With a modem, Nortel technical support can connect to your CallPilot server for troubleshooting purposes. Nortel connects to your server only when you request technical assistance.

Windows automatically recognizes your modem after you connect it and power it on. The power light (PWR LED) does not illuminate until the Windows device driver successfully loads and recognizes the hardware.

To install the modem, you need the following equipment:

•USB modem

•RJ-11 analog phone cord

•USB cable (supplied with the modem)

•an analog line jack

Serial port modems with RS-232 connections are not supported on the 600r.

Step Action

1Connect one end of the USB cable into the modem.

2Connect the other end of the USB cable into USB 2 on the rear panel.

3Connect one end of the telephone cable to the modem RJ-11 jack labeled LINE.

4Connect the other end of the telephone cable to the RJ-11 jack in the wall.

—End—

To connect the external SCSI tape drive

When you connect an external SCSI tape drive, the device must be terminated. Your tape drive comes with a terminator. (See Tape drive terminator in Figure 8 "SCSI tape drive with terminator" (page 31).) The 600r server also comes with a server terminator, a VHDCI (Very High Density Connection Interface) Ultra320 SCSI terminator. (See Server terminator in Figure 8 "SCSI tape drive with terminator" (page 31).) In a previous procedure, you are instructed to connect the server terminator to the SCSI port. Before you connect an external tape drive to the 600r, you must remove the server terminator.

Note: If you do not connect a SCSI device to the server, do not remove the server terminator from the SCSI port.

Nortel CallPilot

600r Server Hardware Installation

NN44200-307 01.03 Standard

5.014 May 2008

Copyright © 2007-2008, Nortel Networks

Image 30

Contents 600r Server Hardware Installation Trademarks Information for Japan Japan Denan statementJapan Vcci statement Page Publication History MayMarch Publication History Contents Contents Chapter How to get help Getting help over the phone from a Nortel Solutions CenterGetting help from the Nortel Web site Getting help through a Nortel distributor or reseller Chapter 600r server description Conventions for WarningsThis chapter Server features Server dimensionsEnvironmental speciﬁcations Front panel featuresSpecification Environmental conditionPower button NMI button not used Reset button ID button Front panelRear panel controls and features Label DescriptionRear panel Label Description PCI riser assembly PCI riser assemblyNetwork connectivity Sample network setup with Meridian Sample network setup MeridianSample network setup Communication Server Sample network setup with Communication ServerSwitch connectivity LAN connectivityNetwork requirements Remote access connectivitySupported peripheral devices Supported peripheral devices Device DescriptionReference documents Installation checklist Chapter Preparing for installationInstallation overview IntroductionGlobal CallPilot Support for Anti-Virus What is next? Unpacking the 600r serverTo unpack the equipment Inspecting the interior of server To remove the server coverTo replace the server cover Inspecting the interior of server Preparing for installation Chapter Installing the server and peripheral devices Installing the serverConnecting peripherals to the server To install the serverRear panel connectors Rear panel Rear panel connectors Label Description To connect the mouse, keyboard, and monitor to the serverTo connect the modem to the server To connect the external Scsi tape driveScsi tape drive with terminator Connecting the server to the Elan subnet Connecting the server to the Nortel server subnet optional Media Access Control addressIf the server Then Installing the Nortel software feature dongle To connect the server to the Nortel server subnetTo install the software feature dongle Dongle plugged in to serverDongle without feature key Installing the software feature keyContinue with Connecting the server to power Installing the server and peripheral devices Locating the power supply modules Chapter Connecting the server to powerSafety precautions Safety informationRack power and grounding Connecting the server to powerAbout the power supply module Before you beginConnecting the server to power To connect the 600r server to power Example setup of 600r with peripheralsWhat is next? Connecting the server to power Chapter EMC emission level protection for the 600r server Ferrite cores secured to an external cable Symbols/Numerics IndexIndex Index Index Page 600r Server Hardware Installation