Rockford Fosgate 300S Mounting Clip Knob, Operation Adjusting Gain, Adjusting Crossover Frequency

Page 11

INSTALLATION

REMOTE PUNCH BASS – (Models 300S, 400S, 500S & 700S Only)

Mounting and installation

1.Find a location, either under the dash or near the center console, that gives easy access to the remote.

2.Using the screws supplied, install the mounting clip with the tabs towards t he back.

3.Route the cable for the remote and connect to both the remote and amplifed subwoofer.

4.Slip the remote onto the mounting clip until it snaps into place.

Mounting

Clip

Knob

5. Install the decal and knob onto the

Decal

remote.

 

OPERATION

ADJUSTING GAIN

Do the following individually for each channel, or both equally if bridged (mono).

NOTE: Models 150S and 200S have a single gain adjustment.

To adjust the gain setting, turn the amplifier gains all the way down. Turn the source unit volume up until distortion is audible and then turn it down a bit until the distortion is inaudible. This will be about two thirds all the way up on most source units. Next, turn the amplifier gain setting until once again distortion is audible and then back it down until the distortion is inaudible. Rockford Fosgate source units do not distort, so the volume can be used at maximum setting.

NOTE: For a more in depth setting procedure, contact Rockford Technical Support.

ADJUSTING CROSSOVER FREQUENCY

Model 200S

Placing the switch in the HP position sets the amplifier to the 120Hz High Pass mode, allowing only frequencies above the cut-off point to pass.

Placing the switch in the AP position sets the amplifier to the All Pass mode, allowing all frequencies to pass.

Placing the switch in the LP position sets the amplifier to the 80Hz Low Pass mode, allowing only frequencies below the cut-off point to pass.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Channel Amplifiers Introduction Table of ContentsContents of Carton Safety InstructionsDesign Features Installation Installation Considerations Mounting Locations InstallationBattery and Charging Wiring the SystemPower Connection Models 150S 200S RCA or High Level input connection Bridged/Mono Wiring All Other Models Channel Wiring Models 150S & 200SSpeaker Impedance Installation Using Passive CrossoversMounting Clip Knob Operation Adjusting GainAdjusting Crossover Frequency Mounting and installationOperation AccessoriesConnecting Punch Capacitors Connecting LinksProcedure 3 Check Amplifier if you experience Turn-on Pop TroubleshootingProcedure 1 Check Amplifier for proper connections Procedure 2 Check Amplifier for audio outputMODEL- Punch SpecificationsShip to Electronics Limited Warranty InformationTable DES Matières FrançaisContenu DE Lemballage Consignes DE Sécurité400S, 500S et 700S Particularités TechniquesInstallation Considérations Concernant L’INSTALLATION Câblage DU Système Emplacements DE MontageBatterie ET Charge Connexion Dalimentation Modèles 150S Et 200S Connexion pour entrée RCA OU de signaux élevés Câblage à 2 voies Tous les autres modèles Câblage à 2 voies Modèles 150S et 200SCâblage ponté/mono Tous les autres modèles Impédance de haut-parleur Installation Utilisation DE FiltresRéglage DE LA Fréquence DU Filtre Passif Installation Basses Punch À TélécommandeFonctionnement Réglage DU Gain Condensateurs de connexion Punch AccessoiresFonctionnement Tous les autres modèlesProcédure 2 vérifiez la sortie audio de l’ampli DépannageCaractéristiques FrançaisSources audio 1 an Haut-parleurs 1 an Informations SUR LA Garantie LimitéeAmplificateurs Punch 2 ans Índice DE Materias IntroducciónContenido DE LA Caja Instrucciones DE SeguridadCorriente Modelos 300S 400S y 500S Conexiones de Modelo 700S Características DEL DiseñoInstalación Consideraciones Para LA Instalación Cableado DEL Sistema InstalaciónLugares DE Montaje Batería Y CargaConexión de Corriente Modelos 150S y 200S Conexiones de Corriente Modelos 300S 400S y 500S Cableado de 2 canales Todos los demás modelos Cableado de 2 canales Modelos 150S y 200SCableado con puente/Mono Todos los demás modelos USO DE X-OVERS Pasivos Transiciones Pasivas Impedancia del altavozMontaje e instalación Broche de Montaje Perilla CalcomaníaFuncionamiento Ajuste DE Ganancia Ajuste DE LA Frecuencia X-OVER Transición Modelo 200SCapacitores conectores Punch FuncionamientoTodos los demás modelos AccesoriosSolución DE Problemas Modelo Punch EspecificacionesAmplificadores Punch 2 años Enviar a ElectronicsInformación Sobre LA Garantía Limitada Inhaltsverzeichnis EinleitungInhalt DES Kartons SicherheitshinweiseModelle 300S 400S, 500S 700S DesigncharakteristikenBefolgen Sie vor dem Einbau diese einfachen Regeln Einbau EinbauüberlegungenVerkabelung DES Systems EinbauBefestigungsstellen Batterie UND AufladungStromanschlüsse Modelle 150S 200S Stromanschlüsse Modelle 300S 400S & 500S Zweikanalverkabelung alle anderen Modelle Zweikanalverkabelung Modelle 150S & 200SÜberbrückete bzw. Monoverkabelung alle anderen Modelle Einbau Verwendung VON Passiven Crossovern LautsprecherimpedanzModell 200S Befestigungs- klemme ReglerBetrieb Lautstärke Gain Einstellen CROSSOVER-FREQUENZ EinstellenPunch Kondensatoren anschließen BetriebAlle anderen Modelle ZubehörOrer FehlerbeseitigungVerfahren 2 Die Audioleistung des Verstärkers prüfen OderMODELL- Punch Technische DatenPUNCH-Verstärker 2 Jahre Informationen ZUR Beschränkten GarantieIndice IntroduzioneContenuto DELL’IMBALLAGGIO Istruzioni DI SicurezzaCollegamenti alla tensione Modelli 300S, 400S, 500S e 700S Caratteristiche DEL DesignCollegamenti Modelli 150S e 200S Alla tensione Modelli 300S, 400S e 500SInstallazione Considerazioni SULL’INSTALLAZIONE Cablaggio DEL Sistema InstallazionePosizionamento Batteria E CaricamentoCollegamento alla tensione Modelli 150S e 200S Cablaggio in parallelo/monofonia Modelli 150S e 200S Cablaggio a 2 canali Tutti gli altri modelli Cablaggio a 2 canali Modelli 150S e 200SCablaggio in parallelo/monofonia Tutti gli altri modelli Impedenza dell’altoparlante Installazione Come Usare LE Frequenze DI Incrocio PassiveRegolazione Della Frequenza DI Incrocio Funzionamento Regolazione DEL GuadagnoTutti gli altri modelli AccessoriCondensatori della Connecting Punch FunzionamentoOppure INDIVIDUAZIONE/RIPARAZIONE GuastiModello Punch SpecificheAmplificatori Punch 2 anni ElectronicsInformazioni Inerenti Alla Garanzia Limitata Rockford Fosgate

400S, 700S, 200S, 300S, 150S specifications

Rockford Fosgate is a renowned brand in the audio industry, particularly known for producing high-performance amplifiers designed for car audio enthusiasts. Among their impressive lineup, the Rockford Fosgate 500S, 150S, 300S, 200S, and 700S stand out for their exceptional sound quality, technological advancements, and robust construction.

The Rockford Fosgate 500S is a powerful amplifier designed to deliver 500 watts RMS in a compact format, catering to those who demand high fidelity in a smaller package. It features a Class D topology, which significantly increases efficiency while maintaining excellent sound clarity. The 500S also incorporates an adjustable crossover and a bass boost feature, allowing users to tailor the audio output to their preferences.

Next, the Rockford Fosgate 150S is a versatile 2-channel amplifier that produces 150 watts RMS. Its compact design makes it an ideal choice for smaller vehicle audio systems or as an addition to an existing setup. Built with high-grade components, the 150S ensures durable performance under pressure and is equipped with a variable low-pass crossover, which enables precise control over the frequency range.

The 300S model delivers 300 watts RMS and is designed for those seeking balance between power and clarity. It features a rugged construction, ensuring longevity, while the smart circuitry protects against overheating, short circuits, and other potential issues. Its custom-tuned enclosure further enhances audio fidelity, providing a seamless listening experience.

The Rockford Fosgate 200S is yet another impressive amplifier, offering 200 watts RMS. It combines excellent power output with a user-friendly interface. The amplifier includes a variable high-pass and low-pass crossover, enabling combinations for various speaker configurations, while its compact size allows easy installation in tight spaces.

Lastly, the 700S amplifier reigns supreme with its 700 watts RMS output, making it a powerhouse for audiophiles seeking the ultimate sound experience. Its advanced thermal management system ensures optimal performance even during extended playback. The 700S supports multiple input formats and is compatible with a range of speakers, solidifying its versatility.

Each of these Rockford Fosgate amplifiers is designed with durability, efficiency, and sound quality in mind. Their advanced technologies and user-friendly features make them ideal for any audio enthusiast looking to elevate their vehicle's sound system. With Rockford Fosgate, users can expect not only powerful amplification but also clarity and precision, ensuring an immersive auditory experience.
Top Page Image Contents