Rockford Fosgate 300S, 700S, 500S, 150S, 200S, 400S manual Installation Installation Considerations

Page 5

DESIGN FEATURES

6.Internal Crossover (Models 150S & 200S) – Is a built-in 12dB/octave Butterworth filter selectable between 120Hz High-Pass (HP),, All Pass (AP), or 80Hz Low-Pass (LP) operation.

6.Variable Crossover (All Other Models) – Is a built-in 12dB/octave Butterworth filter selectable for High-Pass (HP), All Pass (AP), or Low-Pass (LP) operation variable from 50Hz to 210Hz.

7.Gain Control – The input gain control is preset to match the output of most source units. It can be adjusted to match output levels from a variety of source units.

8.RCA Input Jacks – The industry standard RCA jacks provide an easy connection for signal level input. They are gold-plated to resist the signal degradation caused by corrosion.

9.High Level Inputs – The high level inputs use a detachable connector terminated with 20 AWG leads. These inputs should be used if the source unit has only speaker line (high level) outputs and not RCA outputs.

10.Speaker Terminals – These gold-plated connectors are immune to corrosion that can cause signal deterioration. Model 200S utilizes a barrier strip that will accept #10 spade lugs or bare speaker and power wires sized from 10-18 AWG. All other models use heavy duty, gold-plated terminal block connectors (+ and –) will accept wire sizes from 8 AWG to 18 AWG.

INSTALLATION

INSTALLATION CONSIDERATIONS

The following is a list of tools needed for installation:

Volt/Ohm Meter Wire strippers Wire crimpers Wire cutters

#2 Phillips screwdriver Battery post wrench

Hand held drill w/assorted bits 1/8" diameter heatshrink tubing Assorted connectors

Adequate Length—Red Power Wire Adequate Length—Remote Turn-on Wire Adequate Length—Black Grounding Wire

This section focuses on some of the vehicle considerations for installing your new Amplifier. Pre- planning your system layout and best wiring routes will save installation time. When deciding on the layout of your new system, be sure that each component will be easily accessible for making adjustments.

!CAUTION: If you feel unsure about installing this system yourself, have it installed by a qualified technician.

!CAUTION: Before installation, disconnect the battery negative (-) terminal to prevent damage to the unit, fire and/or possible injury.

Before beginning any installation, follow these simple rules:

1.Be sure to carefully read and understand the instructions before attempting to install the Unit.

2.For safety, disconnect the negative lead from the battery prior to beginning the installation.

3.For easier assembly, we suggest you run all wires prior to mounting your Source Unit in place.

4.Route all of the RCA cables close together and away from any high current wires.

5.Use high quality connectors for a reliable installation and to minimize signal or power loss.

6.Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7.Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

8.Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the firewall.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Channel Amplifiers Introduction Table of ContentsContents of Carton Safety InstructionsDesign Features Installation Installation Considerations Battery and Charging InstallationWiring the System Mounting LocationsPower Connection Models 150S 200S RCA or High Level input connection Bridged/Mono Wiring All Other Models Channel Wiring Models 150S & 200SSpeaker Impedance Installation Using Passive CrossoversAdjusting Crossover Frequency Operation Adjusting GainMounting and installation Mounting Clip KnobConnecting Punch Capacitors AccessoriesConnecting Links OperationProcedure 1 Check Amplifier for proper connections TroubleshootingProcedure 2 Check Amplifier for audio output Procedure 3 Check Amplifier if you experience Turn-on PopMODEL- Punch SpecificationsShip to Electronics Limited Warranty InformationTable DES Matières FrançaisContenu DE Lemballage Consignes DE Sécurité400S, 500S et 700S Particularités TechniquesInstallation Considérations Concernant L’INSTALLATION Câblage DU Système Emplacements DE MontageBatterie ET Charge Connexion Dalimentation Modèles 150S Et 200S Connexion pour entrée RCA OU de signaux élevés Câblage à 2 voies Tous les autres modèles Câblage à 2 voies Modèles 150S et 200SCâblage ponté/mono Tous les autres modèles Impédance de haut-parleur Installation Utilisation DE FiltresRéglage DE LA Fréquence DU Filtre Passif Installation Basses Punch À TélécommandeFonctionnement Réglage DU Gain Fonctionnement AccessoiresTous les autres modèles Condensateurs de connexion PunchProcédure 2 vérifiez la sortie audio de l’ampli DépannageCaractéristiques FrançaisSources audio 1 an Haut-parleurs 1 an Informations SUR LA Garantie LimitéeAmplificateurs Punch 2 ans Índice DE Materias IntroducciónContenido DE LA Caja Instrucciones DE SeguridadCorriente Modelos 300S 400S y 500S Conexiones de Modelo 700S Características DEL DiseñoInstalación Consideraciones Para LA Instalación Lugares DE Montaje InstalaciónBatería Y Carga Cableado DEL SistemaConexión de Corriente Modelos 150S y 200S Conexiones de Corriente Modelos 300S 400S y 500S Cableado de 2 canales Todos los demás modelos Cableado de 2 canales Modelos 150S y 200SCableado con puente/Mono Todos los demás modelos USO DE X-OVERS Pasivos Transiciones Pasivas Impedancia del altavozFuncionamiento Ajuste DE Ganancia Broche de Montaje Perilla CalcomaníaAjuste DE LA Frecuencia X-OVER Transición Modelo 200S Montaje e instalaciónTodos los demás modelos FuncionamientoAccesorios Capacitores conectores PunchSolución DE Problemas Modelo Punch EspecificacionesAmplificadores Punch 2 años Enviar a ElectronicsInformación Sobre LA Garantía Limitada Inhaltsverzeichnis EinleitungInhalt DES Kartons SicherheitshinweiseModelle 300S 400S, 500S 700S DesigncharakteristikenBefolgen Sie vor dem Einbau diese einfachen Regeln Einbau EinbauüberlegungenBefestigungsstellen EinbauBatterie UND Aufladung Verkabelung DES SystemsStromanschlüsse Modelle 150S 200S Stromanschlüsse Modelle 300S 400S & 500S Zweikanalverkabelung alle anderen Modelle Zweikanalverkabelung Modelle 150S & 200SÜberbrückete bzw. Monoverkabelung alle anderen Modelle Einbau Verwendung VON Passiven Crossovern LautsprecherimpedanzBetrieb Lautstärke Gain Einstellen Befestigungs- klemme ReglerCROSSOVER-FREQUENZ Einstellen Modell 200SAlle anderen Modelle BetriebZubehör Punch Kondensatoren anschließenVerfahren 2 Die Audioleistung des Verstärkers prüfen FehlerbeseitigungOder OrerMODELL- Punch Technische DatenPUNCH-Verstärker 2 Jahre Informationen ZUR Beschränkten GarantieIndice IntroduzioneContenuto DELL’IMBALLAGGIO Istruzioni DI SicurezzaCollegamenti Modelli 150S e 200S Caratteristiche DEL DesignAlla tensione Modelli 300S, 400S e 500S Collegamenti alla tensione Modelli 300S, 400S, 500S e 700SInstallazione Considerazioni SULL’INSTALLAZIONE Posizionamento InstallazioneBatteria E Caricamento Cablaggio DEL SistemaCollegamento alla tensione Modelli 150S e 200S Cablaggio in parallelo/monofonia Modelli 150S e 200S Cablaggio a 2 canali Tutti gli altri modelli Cablaggio a 2 canali Modelli 150S e 200SCablaggio in parallelo/monofonia Tutti gli altri modelli Impedenza dell’altoparlante Installazione Come Usare LE Frequenze DI Incrocio PassiveRegolazione Della Frequenza DI Incrocio Funzionamento Regolazione DEL GuadagnoCondensatori della Connecting Punch AccessoriFunzionamento Tutti gli altri modelliOppure INDIVIDUAZIONE/RIPARAZIONE GuastiModello Punch SpecificheAmplificatori Punch 2 anni ElectronicsInformazioni Inerenti Alla Garanzia Limitata Rockford Fosgate

400S, 700S, 200S, 300S, 150S specifications

Rockford Fosgate is a renowned brand in the audio industry, particularly known for producing high-performance amplifiers designed for car audio enthusiasts. Among their impressive lineup, the Rockford Fosgate 500S, 150S, 300S, 200S, and 700S stand out for their exceptional sound quality, technological advancements, and robust construction.

The Rockford Fosgate 500S is a powerful amplifier designed to deliver 500 watts RMS in a compact format, catering to those who demand high fidelity in a smaller package. It features a Class D topology, which significantly increases efficiency while maintaining excellent sound clarity. The 500S also incorporates an adjustable crossover and a bass boost feature, allowing users to tailor the audio output to their preferences.

Next, the Rockford Fosgate 150S is a versatile 2-channel amplifier that produces 150 watts RMS. Its compact design makes it an ideal choice for smaller vehicle audio systems or as an addition to an existing setup. Built with high-grade components, the 150S ensures durable performance under pressure and is equipped with a variable low-pass crossover, which enables precise control over the frequency range.

The 300S model delivers 300 watts RMS and is designed for those seeking balance between power and clarity. It features a rugged construction, ensuring longevity, while the smart circuitry protects against overheating, short circuits, and other potential issues. Its custom-tuned enclosure further enhances audio fidelity, providing a seamless listening experience.

The Rockford Fosgate 200S is yet another impressive amplifier, offering 200 watts RMS. It combines excellent power output with a user-friendly interface. The amplifier includes a variable high-pass and low-pass crossover, enabling combinations for various speaker configurations, while its compact size allows easy installation in tight spaces.

Lastly, the 700S amplifier reigns supreme with its 700 watts RMS output, making it a powerhouse for audiophiles seeking the ultimate sound experience. Its advanced thermal management system ensures optimal performance even during extended playback. The 700S supports multiple input formats and is compatible with a range of speakers, solidifying its versatility.

Each of these Rockford Fosgate amplifiers is designed with durability, efficiency, and sound quality in mind. Their advanced technologies and user-friendly features make them ideal for any audio enthusiast looking to elevate their vehicle's sound system. With Rockford Fosgate, users can expect not only powerful amplification but also clarity and precision, ensuring an immersive auditory experience.
Top Page Image Contents