American Dynamics ADCC0300 manual Setting the Keyboard Display Contrast, Viewing Satellite Sites

Page 33

Keyboard Installation and Operation

Setting the Keyboard Display Contrast

1.Press the FUNCTION () and MENU () key.

2.Use the Focus NEAR/Focus FAR key to increase/decrease the display's contrast.

3.When the contrast is satisfactory, press the ENTER key.

Enabling or Disabling the Keyboard Sounder

In the default (factory) setting mode, the keyboard's sounder sounds each time a key is pressed.

To enable/disable the keyboard sounder:

1.Press the FUNCTION () and ENTER key to toggle the sounder between enabled and disabled.

Viewing Satellite Sites

A site is a complete matrix switcher/controller system, providing both local and remote control of resources in a satellite network. If your workstation supports satellite site switching capabilities, this function accesses satellite sites.

To gain access to a satellite site:

1.Enter the site number on the numeric keypad. The number entered will appear on the right hand side of the top line of the LCD display.

2.Hold down the SHIFT () key and press the SITE SELECT () key. The new site number will appear next to "S" on the LCD display.

S03 M0001 C0001

It is now possible to call remote site monitors and cameras by the procedures discussed earlier in this chapter.

25

Image 33
Contents ControlCenterTM Copyright Radio Frequency Emissions Electrical SafetyImmunity EU Conformance StatementSécurité électrique Émission de fréquences radioImmunité Déclaration de conformité UEElektrische Sicherheit FunkfrequenzemissionenImmunität EU-KonformitätserklärungSicurezza elettrica Emissioni in radiofrequenzaImmunità Dichiarazione di conformità UESeguridad eléctrica Emisión de radiofrecuenciaInmunidad Declaración de conformidad de la UEElektrische veiligheid Radiofrequentie-emissieImmuniteit Conformiteitsverklaring van de fabrikantAbout the ADCC0200 and ADCC0300 Keyboard Programming with the ADCC0200/ADCC0300 Keyboards About the ADCC0200 and ADCC0300 Keyboard Key FeaturesADCC0200 and ADCC0300 Keyboard Overview Joystick Page Feature Quick Reference Standard Matrix OperationsRS485 RS232 RS232 RS485 Matrix Menu OperationsDome Operations DirectSet Feature Connection and Setup Ancillary EquipmentMP-KMI Keyboard Matrix Interface Installation Precautions Keyboard Installation and Operation Default setting Multiple Keyboards on an RS485 NetworkTerminating/Biasing the RS485 Network Multiple Keyboards on an RS232 Network User Numbers and Passcodes Basic Operations Operate Mode ADCC0200 and ADCC0300Logging On to the System Logging Off from the SystemSelecting Monitors Keyboard DisplayCalling a Camera to View on a Monitor S01 M000 C0000S01 M013 C0000 S01 M013 C0032 Controlling a Camera’s Pan, Tilt and ZoomControlling the Camera Iris Controlling Camera FocusControlling Camera Flip Auto IrisCalling Presets Auto FocusS01 M001 C0001 Dome Camera DirectSet Running PatternsHolding a Tour Running ToursRestarting a Tour on Hold Stepping through a TourReversing a Tour Calling Salvos RS232 onlyStopping a Tour S01 M013Acknowledging Alarms Calling Views RS485 onlyAuxiliaries Enabling or Disabling the Keyboard Sounder Setting the Keyboard Display ContrastViewing Satellite Sites S03 M0001 C0001Operating a VCR or Digital Recorder Cancel VCR/DVR modeLocking and Unlocking a Camera RS232 only R0021 S01 M013 C0001Initiating F1 Key Commands RS232 only Telemetry Enable/Disable RS485 onlyExiting Program Mode RS232 only Entering Program Mode RS232 onlyProgramming with the ADCC0200/ADCC0300 Keyboards S01 M0001 C0001Matrix Menu Navigating Dome Camera Menus Dome Menu FunctionsSetting Presets Programming Dome PatternsDefining Patterns RS485 only Clearing Patterns RS485 only Initiating F2 Key Commands RS232 onlyDefining Patterns RS232 only Clearing Patterns RS232 onlyEntering the Special Configuration Menu Installer FunctionsSetting the Keyboard Address Setting the Number of Keyboard RetriesSetting the Baud Rate Setting the Network Timeout PeriodTo Reset the Keyboard to its Factory Defaults Selecting RS485 or RS232 modeSelecting Auto Repeat or Make/Break Keypress Mode Disabling/Enabling the Sounder1234 Enter Passcode Setting the Passcode Program Lock FunctionAppendix a ADCC0200/ADCC0300 VCR Reprogramming Label Key Default CommandFollowing text should initially be shown on the teminal Monitor Arming Code Monitor Acronym Command Sequence Appendix B Monitor Arming CommandsProblem Check List Appendix C TroubleshootingAppendix D Specifications Index Keyboard Installation and Operation ADCC0200 and ADCC0300 Keyboard Installation and Operation ADCC0200 and ADCC0300 Keyboard Installation and Operation Please visit our website for more information