American Dynamics ADCC0300, ADCC0200 manual Connection and Setup, Ancillary Equipment

Page 19

Keyboard Installation and Operation

Chapter 2: Connection and Setup

This chapter describes the power and data connections between the ADCC0200/ ADCC0300 keyboard and the switching system being used.

IMPORTANT NOTE

The default setting for the keyboard is RS485 mode at 19200 baud. To change these settings, enter the Special Config menu by pressing SHIFT () and CLEAR () keys within five seconds of powering up the keyboard. Then press one of the following:

to change baud rate.

to change the mode (ADNet RS485, RS232).

to select Auto Repeat or Make/Break mode. See the matrix manual for correct setting. to enable/disable the speaker.

For other functions, please see Chapter 5.

Ancillary Equipment

The keyboard is supplied with one seven foot (2 meters) MP-CBL data connection cable. The MP-KMI keyboard matrix interface (optional) is also supplied with a MP-CBL data connection cable.

The power supply is connected to the jack connector of the MP-KMI keyboard matrix interface. The power supply must be a Class 2 type UL listed 12V DC component.

MP-KMI Keyboard Matrix Interface

The MP-KMI keyboard matrix interface contains two RJ-45 connectors connected to a five-way screw terminal block. The Matrix connector is connected to the switching system and the Keyboard connector to the keyboard using the MP-CBL cable supplied.

Power is supplied to the keyboard via the power connector built in to the MP-KMI.

The power supply is limited to 15W by a 500mA UL listed fuse.

11

Image 19

Contents ControlCenterTM Copyright EU Conformance Statement Electrical SafetyRadio Frequency Emissions ImmunityDéclaration de conformité UE Émission de fréquences radioSécurité électrique ImmunitéEU-Konformitätserklärung FunkfrequenzemissionenElektrische Sicherheit ImmunitätDichiarazione di conformità UE Emissioni in radiofrequenzaSicurezza elettrica ImmunitàDeclaración de conformidad de la UE Emisión de radiofrecuenciaSeguridad eléctrica InmunidadConformiteitsverklaring van de fabrikant Radiofrequentie-emissieElektrische veiligheid ImmuniteitAbout the ADCC0200 and ADCC0300 Keyboard Programming with the ADCC0200/ADCC0300 Keyboards About the ADCC0200 and ADCC0300 Keyboard Key FeaturesADCC0200 and ADCC0300 Keyboard Overview Joystick Page Standard Matrix Operations Feature Quick ReferenceRS485 RS232 RS232 RS485 Matrix Menu OperationsDome Operations DirectSet Feature Ancillary Equipment Connection and SetupMP-KMI Keyboard Matrix Interface Installation Precautions Keyboard Installation and Operation Multiple Keyboards on an RS485 Network Default settingTerminating/Biasing the RS485 Network Multiple Keyboards on an RS232 Network Logging Off from the System Basic Operations Operate Mode ADCC0200 and ADCC0300User Numbers and Passcodes Logging On to the SystemS01 M000 C0000 Keyboard DisplaySelecting Monitors Calling a Camera to View on a MonitorS01 M013 C0000 S01 M013 C0032 Controlling a Camera’s Pan, Tilt and ZoomAuto Iris Controlling Camera FocusControlling the Camera Iris Controlling Camera FlipAuto Focus Calling PresetsS01 M001 C0001 Dome Camera DirectSet Running PatternsStepping through a Tour Running ToursHolding a Tour Restarting a Tour on HoldS01 M013 Calling Salvos RS232 onlyReversing a Tour Stopping a TourCalling Views RS485 only Acknowledging AlarmsAuxiliaries S03 M0001 C0001 Setting the Keyboard Display ContrastEnabling or Disabling the Keyboard Sounder Viewing Satellite SitesR0021 S01 M013 C0001 Cancel VCR/DVR modeOperating a VCR or Digital Recorder Locking and Unlocking a Camera RS232 onlyInitiating F1 Key Commands RS232 only Telemetry Enable/Disable RS485 onlyS01 M0001 C0001 Entering Program Mode RS232 onlyExiting Program Mode RS232 only Programming with the ADCC0200/ADCC0300 KeyboardsMatrix Menu Navigating Dome Camera Menus Dome Menu FunctionsProgramming Dome Patterns Setting PresetsDefining Patterns RS485 only Clearing Patterns RS232 only Initiating F2 Key Commands RS232 onlyClearing Patterns RS485 only Defining Patterns RS232 onlySetting the Number of Keyboard Retries Installer FunctionsEntering the Special Configuration Menu Setting the Keyboard AddressSetting the Baud Rate Setting the Network Timeout PeriodDisabling/Enabling the Sounder Selecting RS485 or RS232 modeTo Reset the Keyboard to its Factory Defaults Selecting Auto Repeat or Make/Break Keypress Mode1234 Enter Passcode Setting the Passcode Program Lock FunctionAppendix a ADCC0200/ADCC0300 VCR Reprogramming Label Key Default CommandFollowing text should initially be shown on the teminal Monitor Arming Code Monitor Acronym Command Sequence Appendix B Monitor Arming CommandsProblem Check List Appendix C TroubleshootingAppendix D Specifications Index Keyboard Installation and Operation ADCC0200 and ADCC0300 Keyboard Installation and Operation ADCC0200 and ADCC0300 Keyboard Installation and Operation Please visit our website for more information