Nortel Networks 4400, RELEASE 4.1 manual EC Declaration of Conformity, Limitations of Remedies

Page 3

3

EC Declaration of Conformity

This product conforms (or these products conform) to the provisions of Council Directive 89/336/EEC and 73/23/ EEC. The Declaration of Conformity is available at Nortel Networks, 4100 Guardian Street Simi Valley, CA 93065 attention: Regulatory Department.

LIMITATIONS OF REMEDIES

Nortel’s entire liability and Customer’s exclusive remedies are as follows: Nortel shall (i) use commercially reasonable efforts to correct any failure of the software program, of which it is given written notice by Customer during the Warranty Period, to perform substantially in accordance with the documentation, provided such failure can be recreated by Nortel in an unmodified version of the software program, or if Nortel is unable to correct such failure the software program and documentation may be returned and the license fee paid will be refunded, or (ii) replace any diskette not meeting Nortel’s “Limited Warranty” or, if Nortel is unable to deliver a replacement diskette which is free from defects in materials or workmanship, the software program and documentation may be returned and the license fee paid will be refunded.

IN NO EVENT WILL NORTEL OR ITS SUPPLIERS BE LIABLE TO CUSTOMER FOR ANY LOST PROFILES, LOST SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM EVEN IF NORTEL HAS BEEN ADVISED OF THE POSSIBLITY OF SUCH DAMAGES. THE LIABILITY OF NORTEL, IF ANY, FOR DAMAGES RELATING TO ANY NORTEL SOFTWARE PRODUCT SHALL BE LIMITED TO THE ACTUAL AMOUNTS PAID BY CUSTOMER FOR SUCH SOFTWARE PRODUCT.

SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSIONS OR LIMITATION MAY NOT APPLY.

Getting Started with Passport 4400, Release 4.1

Image 3
Contents Getting Started with Passport 4400, Release Statement of Conditions Copyright 2000 Nortel Networks, IncTrademarks Restricted Rights LegendLimitations of Remedies EC Declaration of ConformityTechnische Daten Donnees Techniques Safety Warnings and CautionsTechnical Data WarnungAvertissementNotification of Canadian Requirements Notification of FCC Requirements209664-A Contents Chapter Accessing the CLI and Basic Configuration Index Contents 209664-A Chapter Introduction Unpacking the Unit List of DocumentationPassport software license Device Management Tools Determining Which Management Tool to UsePassport 4400 Install Network Management Tools Pmdm Introduction 209664-A Chapter Online Documentation Accessing the Online DocumentationOpen the documentation For installing documentation from the CD-ROMNavigating Online Documentation Online Documentation Site Map Online Documentation Printing Online Documentation Browsers Browser How to Get Optimum Results Operation Passport 4400 Rel Software Online Documentation 209664-A Chapter Hardware Setup If you are using You needWorkstation Requirements If you are using Refer to Installing Passport 4460 HardwareChapter Configurator Procedure for Creating a Node Profile Accessing the Configurator Through a Web Browser Viewing Node Profile Information Defining a Unique DNA Prefix Click on ConfigureDefining a Node ID on Defining a Customer ID on Defining a Node NameDefining a Node ID Defining a Customer ID Resetting the UnitSetting the DNA Numbering Plan Overriding the DNA Numbering Plan Passport 4400 Configurator Documentation URL UpdateSetting the System Clock Configurator Procedure for Creating a Node Profile Configurator Procedure for Creating a Node Profile 209664-A Using a Terminal Chapter Accessing the CLI and Basic ConfigurationCommunication Parameter Set-Up Requirements Accessing the CLI and Basic Configuration Hardware in the flow control field Logging into the CLI Using the Terminal Emulation ProgramAssigning the IP Address Parameter Range of Values Required Actions Chapter CLI Procedure for Creating a Node Profile CLI Procedure for Creating a Node Profile Parameter Range of Values Required Action Defining Node ID on Defining Customer ID on Defining Node ID Defining Customer IDParameter Range of Value Required Action Saving the Current Configuration and Resetting the Unit Confirming the New ConfigurationSetting the System Clock CLI Procedure for Creating a Node Profile IfIndex Overview Appendix a IfIndexes and Interface IdentificationHard-Coded IfIndexes Reserved IfIndexes and RangesIfIndex Description Safe IfIndex Ranges IfIndex RangesIfIndex Table Display Description Configurator Procedure for Displaying the IfIndex TableCLI Procedure for Displaying the IfIndex Table IfIndex IfExtTypeSlot PPA Number IfIndex Table Display DefinitionsChannel Number Slot NameAppendix a IfIndexes and Interface Identification 209664-A Application Code Appendix B Installing System Software from the CD-ROMDownloading Application Software Configurator Procedure for Downloading Application SoftwareCommit the Application Code Bank Select Administration and Code BankSave the Current Configuration and Reset the Unit CLI Procedure for Downloading Application Software Appendix B Installing System Software from the CD-ROM Babt CSA FCC TUV IndexIndex Index Index 209664-A