GBC F-36 manual Power Cord Connection

Page 17

F-36 PRO Laminator Operation Manual

Installation

 

 

WARNING

ALWAYS CHECK THE SENSORS PRIOR TO OPERATION! The sensors must be clean and contact the roll to maintain proper roll operating temperatures. The rolls can overheat and cause a fire or seriously damage the laminator.

7.Plug the laminator into an approved socket or have a certified electrician wire the laminator directly to a power source.

The laminator requires 30A single phase service and a power receptacle that accepts a 30A 250V NEMA L6-30P plug or, in Europe, 3 phase, 240/ 400 VAC with 20A per phase. See Figure 2-6 for power cord connection options.

8.Replace both cabinet covers.

EUROPEAN

LINE 1

3–PHASE Y

A

 

 

N

 

LINE 3

 

LINE 2

 

A

 

 

 

 

THE EUROPEAN

 

 

THREE-PHASE (STAR)

 

 

 

 

 

LINE–1

 

 

 

 

 

LINE–2

 

 

 

 

 

LINE–3

 

 

 

 

 

N

 

 

 

 

 

 

 

SINGLE PHASE (U.S.)

LINE 1

 

 

 

 

 

 

 

 

 

JUMPER

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LINE 2

U.S. SINGLE PHASE

JUMPER

LINE 1

LINE 2

Figure 2-6: Power Cord Connection

© GBC Pro-Tech 1999 January

2-7

Image 17
Contents           GBC Pro-Tech 1999 January     Preinstallation Checklist Unpacking Setup StartupMachine Shutdown     Using the Emergency Stop Buttons SafetyGBC Pro-Tech 1999 January  & $*  *  Locations of Safety Labels Decal Meaning    # + Position the jumpers as shown in -6 for Service choice  !   Laminator Space Requirements InstallationIf the laminator is in a cardboard box  +$Tools required Foot Bolt Shipping Pad Removing the Crate If the laminator is in a crate  Setup ProcedurePower Cord Connection Startup Checklist          Operation $#  -# $#  $   #  $   $ Then mountedInsert a starter board into the nip and lower  # #-   34*6!575 Identification Diagram34*/5 One-Pass Mounting and Laminating 34*/534*6!575 One-Pass Mounting 34*/534*6!575 Two Pass Mount and Cold/Pressure Overlaminate, First Pass 34*/5534*6!5755 Two Pass Mount and Cold/Pressure Overlaminate, Second Pass 34*/5834*6!5758 Two Pass Mount and Hot Overlaminate, First Pass 34*/5%534*6!575%5 Two Pass Mount and Hot Overlaminate, Second Pass 34*/5%834*6!575%8 Encapsulation 34*/534*6!575   #$ Firmly hold the thermocouple where the guitar Maintenance and TroubleshootingUpper Main To clean beads of adhesive, dust and dirt from the rolls To clean the laminator rolls9$# 4 To clean the cabinet and covers#  $ To adjust the chain tension $ #        #$7 . &  This warranty specifically does not coverUnauthorized customer alterations will void this Warranty Warranty Quantity Part Description RecommendedSpecifications Nip 1-1, 1-2, 2-6, 2-8, 3-1, 4-1, 4-4, 4-5  Index