GBC F-36 manual   ,  $ #  

Page 41

F-36 PRO Laminator Operation Manual

Maintenance and Troubleshooting

 

 

*  

Tools required:

1/8" hex wrench

High temperature grease or lithium grease

Grease gun

To lubricate the laminator:

WARNING

Do not lubricate the laminator when it is hot. You

can be burned.

WARNING

Unplug the laminator and lockout power while you are performing this procedure. You could be severely shocked, electrocuted, or get your fingers caught in the drive mechanisms.

1.Remove the drive and control side cabinet covers using the 1/8" hex wrench by removing the six screws holding each cover in place.

2.Using the grease gun, lubricate each grease fitting (shown in Figure 4-7) with one squirt of high tem- perature grease.

Grease

WA

 

 

 

RN

 

SEEN GANG

 

A

 

IN

 

CH

TU

G

 

MI

 

Fittings

 

 

 

RDE

 

 

 

 

 

Mo

 

 

 

 

cr vin

 

 

 

us

gp

 

 

 

Do handartsc

 

 

do not

cut.an

 

orooper

 

 

 

pen.ate

with

 

 

 

 

Figure 4-7: Grease Fittings

3.Lubricate the chain using a soft cloth and automo- tive oil.

4.Replace the cabinet covers and reconnect power to the laminator.

 $ #  

For machine parts and technical service in North America, please call: 1-800-790-7787. Please provide serial number when calling for service. In Europe, please call: +44 (0) 1844 202 440 or fax: +44 (0) 1844 202 441.

For film and application questions in North America, please call 1-800-236-8843. In Europe, please call: +44

(0) 1844 202 440 or fax: +44 (0) 1844 202 441.

© GBC Pro-Tech 1999 January

4-7

Image 41
Contents           GBC Pro-Tech 1999 January     Preinstallation Checklist Unpacking Setup StartupMachine Shutdown     Using the Emergency Stop Buttons SafetyGBC Pro-Tech 1999 January  & $*  *  Locations of Safety Labels Decal Meaning    # + Position the jumpers as shown in -6 for Service choice  !   Laminator Space Requirements InstallationIf the laminator is in a cardboard box  +$Tools required Foot Bolt Shipping Pad Removing the Crate If the laminator is in a crate  Setup ProcedurePower Cord Connection Startup Checklist          Operation $#  -# $#  $   #  $   $ Then mountedInsert a starter board into the nip and lower  # #-   34*6!575 Identification Diagram34*/5 One-Pass Mounting and Laminating 34*/534*6!575 One-Pass Mounting 34*/534*6!575 Two Pass Mount and Cold/Pressure Overlaminate, First Pass 34*/5534*6!5755 Two Pass Mount and Cold/Pressure Overlaminate, Second Pass 34*/5834*6!5758 Two Pass Mount and Hot Overlaminate, First Pass 34*/5%534*6!575%5 Two Pass Mount and Hot Overlaminate, Second Pass 34*/5%834*6!575%8 Encapsulation 34*/534*6!575   #$ Firmly hold the thermocouple where the guitar Maintenance and TroubleshootingUpper Main To clean beads of adhesive, dust and dirt from the rolls To clean the laminator rolls9$# 4 To clean the cabinet and covers#  $ To adjust the chain tension $ #        #$7 . &  This warranty specifically does not coverUnauthorized customer alterations will void this Warranty Warranty Quantity Part Description RecommendedSpecifications Nip 1-1, 1-2, 2-6, 2-8, 3-1, 4-1, 4-4, 4-5  Index