Toshiba H-9000N Speed KEY Setting, Setting Department/Vendor Number, Department Number, ESC Menu

Page 39

9.PROGRAMMING PROCEDURES

9.10 SPEED KEY SETTING

9.10SPEED KEY SETTING

Menu Page: 1

Item No.: 9

The H-9000 has a maximum of 70×2 speed keys which are very convenient to call PLUs quickly. (Refer to page 5-3 regarding the Key Layout.)

<MENU>

Page 1

 

i

9

Enter the Speed

Key number

 

(# 1～70 on each page)

 

◇

Toggles the speed

 

NEXT

or

 

key Page

 

PLU

 

ENTER

Enter the PLU#. (max. 6 dig.)

ENTER

i

PROG.

ESC.

<MENU>

Page 1

Main

<MENU>

■Setting Department/Vendor Number

<MENU>

9

 

 

 

Page 1

 

 

 

 

 

 

 

 

AUTO

Enter the default

ENTER

 

CODE

department #.

(1～99)

 

 

Enter the speed key number.

ENTER

◇

Enter the department #

or vendor #.

(1～99)

 

 

Selecting items to be assigned to speed keys.

(PLU #/VENDOR #/DEPT #/)

ENTER

PROG.

ESC.

<MENU>

Page 1

Main

<MENU>

●Department Number

When initial set #10-6 is set to “1”, the six-digit PLU # is divided into two; the upper two digits are assigned to department #, and the lower four digits to PLU.

The department # is automatically added in the front of the four-digit PLU # and treated as a six-digit PLU #.

In case of “PROG.”, “Report”, and “Reset” modes, PLU # is treated as a six-digit number. So the upper two digits are not treated as department #. Consequently the four-digit PLU # is available only in “REG.”, “M.DOWN”, and “REWRAP” modes.

NOTE: The default Dept No. is a two- digit serial number ranging from o to 99. Entering a “0” clears a Dept. No.

●Vendor Number

Vendor numbers can be be set when the Initial Setting #11-1 is set to 1.

Vendor numbers are assigned to the speed keys in two ways:

①Individual vendor number: 00-39

Vendor # is assigned to the speed keys one by one.

②Group vendor number: 0-, 1-, 2- and 3-

Maximum 10 vendor numbers can be assigned to one speed key, resulting in 4 speed keys in total. When assigning group vendor numbers to the speed keys, enter the first digit of the vendor key (0, 1, 2 or 3) plus a bar (-).

Vendor numbres can be called whichever half of the speed keys are selected.

9- 17

Page 38 Page 40
Image 39
Page 38 Page 40
Contents 9000N-US Page Safety Summary Precautions Table of Contents Programmed Data Verification Reports ･･････････････････････ Issuing Labels with NET Weight Statement ･･････････････Introduction Accessories Applicable Model∙ H-9000-N-US Description of the model number is as follows Printer SpecificationTmcc OptionLON STLAN-2PDisplay AppearanceKEY Layout Programming KeyboardProgramming Keyboard Function Space SendProg Operation Keyboard and Speed Keyboard Operation Keyboard FunctionPLU Void PRTFor DT/TMZero Self Service KeyboardKEY Layout Speed KEY SET Procedure Before OperationRemoval and Replacement of Media Removal and Replacement of Media Outline of Operation PowerTmcc CMT-port communicarion Clerk Label Registration modeXNOT Available 1/4LB KEY 100g, kg KEY LB/kg KEYHow to access the Programming Menu Programming ProceduresTitle and Contents of Programming Menu TEC Store How to enter charactersMenu PLU Data EditFor the UPC# PLU Data SettingAuto Code Ingredient Message Nutrition Setting When entering PLU#, be careful of the following Set the Daily Value Table Daily Value Max digits Contents of Daily valueMemory file is sorted when a memory full error occurs Deleting Nutrition DataMemory file sort Menu Item No Verifies PLU data stored in the scale PLU Verifying LabelAddress and Commercial Message Setting Message construction Message display time Combination MessageThank YOU ANK YOU Call AGA Scrolling Flashing Curtaining Scrolling up Scrolling downThank YOU Thank YOU CallGrade Line Special InformationVendor Number Speed KEY SettingSetting Department/Vendor Number Department NumberBy pressing Key Print FormatFormat No Label Format Number TableDATE/TIME Setting Menu Item NoCMT Operations Program the file Error code during PL-3 operationNumber of the data disc by using the rotary switch PL-3 OperationTransmission Item List Item #CMT IN-LINE/LOCAL Transmission Delay Time TableLON System Initial #0 #19 Cancel RetryData Transmission Price② By Count Format Default Bar Code FormatBAR Code Format ① Weigh or Fix Price FormatPLU # UPC # PC/D Flag PLU # UPC # PC/D Price WeightTitles Verify H-9000=CMT Transferring Logo DataError message during data transmission Idiom SettingVendor Setting Free Format Setting Key functionsEnter SP-INFO/NET WT Logo Frequent Shopper Print coordinate How to access Report menu Programmed Data Verification ReportsMenu Set the zone PLU #. Ex. PLU #100 ～108 R S X Z Password SecuritySetting Password and Protect Menu R S× ー × Calling Menu by Entering Password How to access REG., M.DOWN, or Rewrap menu Operating ProceduresWeighing Operation Menu REG., M.DOWN, or Rewrap Mode WeighFIX Price Operation REG. MANU. BY-COUNT Donuts By Count OperationFor To check the remaining number, clear the PLU and press Key Print Count OperationExample B When operating in Fix or By Count mode Set the number of labels. Max labels Enter the PLU # PLU Issuing Labels with NET Weight StatementSample label 12-10 Platter TARE/SAVE Function ProceduresCalling and Printing Grade Lines Logo Calling and Printing LogosSelecting Print Item Menu REG, M.DOWN, or Rewrap Mode WEIGH, FIX, or by CountDate Change Batch Print Mode with 30 Items Run Assignment Unit Price Change and G.Line/LOGO Call Label Issue Stop or Cancel Dpt # Visual Commodity LibraryFloating Vendor Subtotal Price deletionTotal Operation How to access Read or Reset menuEx. Report Menu Hourly Total ReportGrand Total Report PLU Total ReportFor Enter PLU Total Vendor Total ReportProgramming Mode Error Message TableReport and Reset Mode Label lssue ModeLON System Mode Cleaning the Print Head Before You Call for Service TroubleshootingPage
Top Page Image Contents