Toshiba H-9000N-US, EO1-32004 Operating Procedures, How to access REG., M.DOWN, or Rewrap menu

Page 63

12. OPERATING PROCEDURES

■ NOTES BEFORE STARTING OPERATION

12. OPERATING PROCEDURES

■NOTES BEFORE STARTING OPERATION

(1) Insert the power plug into the AC outlet and turn the power ON.

(2) A sixteen-second scanning will be performed after pressing the POWER key.

(3)Do not move the unit while it is in operation. Should it become necessary to move it at any time, turn the power switch to the OFF position and be sure to readjust the level indicator after relocating the scale*.

(4)Should a power failure occur during operation, remove the commodity from the platter and insert the power plug into an AC outlet again when power is restored.

(5)If the printer is used with an unrated power source, inaccurate scaling* or other errors may occur.

(6)If the zero point has shifted during scaling, and no tare is displayed, adjust the zero point by depressing the ZERO key*.

(7)Check the date of the printer before operation every day.

(8)Make a test print before operation every day. Press the TEST key, and the test label is issued.

*: Available only when the optional scale unit is connected.

■How to access REG., M.DOWN, or REWRAP menu

The following display is the REG. menu display. When this display is shown after pressing the POWER key, you can start the REG. operation right away.

<REG.> MANU. BY-COUNT

ENTER THE PLU #

	lb	UNIT/$	TOTAL $
	- - - - -	P	000000

To access a menu from other menus, press the ESC. key to show the Main menu and enter the menu No. When the M.DOWN and REWRAP menus are protected, enter the menu No. and then the password.

<Menu> MAIN
0.	PROG.	5.	READ
1.	REG.	6.	RESET
2.	MARK DOWN	7.
3.	REWRAP	8.
4.	SECURITY	9.

NOTE: If a label nothing is printed or is issued after a printed label in batch mode, refer to Section 9.11 and press the SET NEXT key.

12- 1

Image 63

Contents 9000N-US Page Safety Summary Precautions Table of Contents Programmed Data Verification Reports ･･････････････････････ Issuing Labels with NET Weight Statement ･･････････････Introduction Accessories Applicable Model∙ H-9000-N-US Description of the model number is as follows Printer SpecificationTmcc OptionLON STLAN-2PDisplay AppearanceKEY Layout Programming KeyboardProgramming Keyboard Function Space SendProg Operation Keyboard and Speed Keyboard Operation Keyboard FunctionPLU Void PRTFor DT/TMZero Self Service KeyboardKEY Layout Speed KEY SET Procedure Before OperationRemoval and Replacement of Media Removal and Replacement of Media Outline of Operation PowerTmcc CMT-port communicarion Clerk Label Registration modeXNOT Available 1/4LB KEY 100g, kg KEY LB/kg KEYHow to access the Programming Menu Programming ProceduresTitle and Contents of Programming Menu TEC Store How to enter charactersMenu PLU Data EditFor the UPC# PLU Data SettingAuto Code Ingredient Message Nutrition Setting When entering PLU#, be careful of the following Set the Daily Value Table Daily Value Max digits Contents of Daily valueMemory file is sorted when a memory full error occurs Deleting Nutrition DataMemory file sort Menu Item No Verifies PLU data stored in the scale PLU Verifying LabelAddress and Commercial Message Setting Message construction Message display time Combination MessageThank YOU ANK YOU Call AGA Scrolling Flashing Curtaining Scrolling up Scrolling downThank YOU Thank YOU CallGrade Line Special InformationVendor Number Speed KEY SettingSetting Department/Vendor Number Department NumberBy pressing Key Print FormatFormat No Label Format Number TableDATE/TIME Setting Menu Item NoCMT Operations Program the file Error code during PL-3 operationNumber of the data disc by using the rotary switch PL-3 OperationTransmission Item List Item #CMT IN-LINE/LOCAL Transmission Delay Time TableLON System Initial #0 #19 Cancel RetryData Transmission Price② By Count Format Default Bar Code FormatBAR Code Format ① Weigh or Fix Price FormatPLU # UPC # PC/D Flag PLU # UPC # PC/D Price WeightTitles Verify H-9000=CMT Transferring Logo DataError message during data transmission Idiom SettingVendor Setting Free Format Setting Key functionsEnter SP-INFO/NET WT Logo Frequent Shopper Print coordinate How to access Report menu Programmed Data Verification ReportsMenu Set the zone PLU #. Ex. PLU #100 ～108 R S X Z Password SecuritySetting Password and Protect Menu R S× ー × Calling Menu by Entering Password How to access REG., M.DOWN, or Rewrap menu Operating ProceduresWeighing Operation Menu REG., M.DOWN, or Rewrap Mode WeighFIX Price Operation REG. MANU. BY-COUNT Donuts By Count OperationFor To check the remaining number, clear the PLU and press Key Print Count OperationExample B When operating in Fix or By Count mode Set the number of labels. Max labels Enter the PLU # PLU Issuing Labels with NET Weight StatementSample label 12-10 Platter TARE/SAVE Function ProceduresCalling and Printing Grade Lines Logo Calling and Printing LogosSelecting Print Item Menu REG, M.DOWN, or Rewrap Mode WEIGH, FIX, or by CountDate Change Batch Print Mode with 30 Items Run Assignment Unit Price Change and G.Line/LOGO Call Label Issue Stop or Cancel Dpt # Visual Commodity LibraryFloating Vendor Subtotal Price deletionTotal Operation How to access Read or Reset menuEx. Report Menu Hourly Total ReportGrand Total Report PLU Total ReportFor Enter PLU Total Vendor Total ReportProgramming Mode Error Message TableReport and Reset Mode Label lssue ModeLON System Mode Cleaning the Print Head Before You Call for Service TroubleshootingPage