Toshiba B-852-TS12-QQ owner manual A4.7.3 Magnified Views of Slant Line Pattern, Letter

Page 108

APPENDIX 4 SYSTEM MODE

EO1-33029

A4.7 Additional Information

A4.7.2 Maintenance Counter/Parameter Check Print Sample and Descriptions (Cont.)

No.

Item

Contents

(34)

Printer IP address

***.***.***.***

(35)

Gateway IP address

***.***.***.***

(36)

Subnet mask

***.***.***.***

(37)

True type font registration area size

0 KB to 896 KB (unit of 64 KB)

(38)

External character registration area size

0 KB to 896 KB (units of 64 KB)

(39)

Basic file store area size

0 KB to 896 KB (units of 64 KB)

(40)

PC saving area size

0 KB to 896 KB (units of 64 KB)

(41)

PCL Emulation

ON: Available

OFF: Unavailable

 

 

(42)

Print speed for PCL emulation

4”/sec.

2”/sec.

 

 

 

 

NONE: None

(43)

Sensor type for PCL emulation

REFLECT: Black mark sensor

 

 

TRANS: Feed gap sensor

(44)

Printing mode for PCL emulation

TRANSFR: Thermal transfer

DIRECT: Thermal direct

 

 

(45)

Issue mode for PCL emulation

[S] NO CUT: Batch mode with no cut

[C]WITH CUT: Cut mode

 

 

 

 

A4

(46)

Media size for PCL emulation

LEGAL

LETTER

 

 

 

 

User

 

 

ON: Available

(47)

Socket port number

OFF: Unavailable

 

 

Port No. 0 to 65535

(48)

BASIC interpreter setting

ON: Available

OFF: Unavailable

 

 

(49)

BASIC interpreter trace setting

ON: Available

OFF: Unavailable

 

 

A4.7.3 Magnified Views of Slant Line Pattern

∙1-dot Slant Line (Black Area Ratio: 16.7%)

∙3-Dot Slant Line (Black Area Ratio: 16.7%)

A4-30

Page 107 Page 109
Image 108
Page 107 Page 109
Contents 852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents A1-1 A2-1A3-1 A4-1Introduction Features Product OverviewUnpacking Accessories Dimensions AppearanceFront View Rear View Operation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Assembling the Accessories Assembling the Supply Holder FrameConnecting the Cables to Your Printer Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Installing the Media onto the Supply Holder Unit Disassembling the Supply Holder UnitInstalling the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Printer BelowSetting Sensor Positions Setting the Feed Gap SensorSetting the Black Mark Sensor Loading the Ribbon Inserting the Optional Pcmcia Cards COMTest Print At the same time Test Print Printer Operation Overview Operating ModesOperating Modes Installing the Printer Drivers System RequirementsDriver Download SystemEO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Details Tab Print to the followingPrint using ∙ Click Capture Printer Port Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Stock Tab Stock Tab Sensor Select Stock Tab Options Tab Options tab, the following display screen will appearTesting Tab Testing Tab Testing Tab Testing Tab About Tab About Tab On Line Mode Operation PanelOperation Reset Dump Mode Restart keyPrint Conditions Receive buffer sizeMaintenance CleaningPrint Head/Platen/ Sensors Care/Handling of the Media and Ribbon Troubleshooting Error MessagesError Messages Problems/Causes Solutions Possible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Removing Jammed Media Threshold Setting „Threshold setting procedureFeed key Appendix 1 Specifications A1.1 PrinterModel 852-TS12-QQ A1.2 Options A1.3 MediaA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and LedsFollowing message appears Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelIf the power is turn on while A4.2 OverviewA4.3 Self-Diagnostic Test Printing mode selectionMaintenance counter/parameter settings print out Self-Diagnostic Test and the result print out Print head element checkA4.4 Printer Parameter Fine Adjustment Feed Length Fine Adjustment Restart FeedCut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Rewind Motor Feed MotorA4.4 Printer Parameter Fine Adjustment Cont Threshold Manual Fine Adjustment Black Mark/Feed Gap SensorBlack Mark Sensor Feed Gap SensorPrint Condition Setting A4.5 Test PrintTest Pattern Selection Issue Count Setting Specifying the Print Condition for the Test PrintPrint Speed Setting Printing Mode SelectionSensor Type Selection Issue Mode Selection Label Length SettingPaper Feed Selection Test Print Pattern Selection Pause keySlant Line 1 dot Slant Line 3 dotsCharacters BarcodeNon-Printing Factory TestA4.6 PCL Emulation Setting Auto PrintEmulation ON/OFF Selection Print SpeedSensor Type Selection Issue Mode Selection Media Width SettingMedia Size Selection Media Length Setting A4.7.1 Self-Diagnostic Test Result Sample and Descriptions A4.7 Additional InformationSdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD A4.7.3 Magnified Views of Slant Line Pattern LetterAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Bar codePre-printed media Index Index Page
Top Page Image Contents