Toshiba B-852-TS12-QQ owner manual On Line Mode, Operation Panel

Page 61

4. ON LINE MODE

4. ON LINE MODE

EO1-33029

4.1 Operation Panel

4.1 Operation Panel

This chapter describes usage and purpose of the keys on the Operation Panel in On Line Mode.

When the printer is in On Line Mode and connected to a host computer, normal operation of printing images on labels or tags can be accomplished.

∙The figure below illustrates the Operation Panel and key functions.

LCD Message Display

POWER LED (Green)

[RESTART] key

[FEED] key

POWER ON LINE ERROR

FEED RESTART PAUSE

ON LINE LED (Green)

ERROR LED (Red)

[PAUSE] key

NOTE:

Use the [RESTART] key to resume printing after a pause condition, or after clearing an

error.

The LCD Message Display shows messages in alphanumeric characters and symbols to indicate the printer’s status. Up to 16 characters can be displayed on one line.

There are three LED lights on the Operation Panel.

LED	Illuminates when…	Flashes when…
POWER	The printer is turned on.	-----
ON LINE	The printer is ready to	The printer is
	print.	communicating with
		your computer.
ERROR	Any error occurs with	-----
	the printer.	-----
	the printer.

There are three keys on the Operation Panel.

PAUSE	Used to stop printing temporarily.
RESTART	Used to restart printing.
FEED	Used to feed the media.

4- 1

Image 61

Contents 852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents A2-1 A1-1A3-1 A4-1Product Overview Introduction FeaturesUnpacking Accessories Appearance DimensionsFront View Rear View Interior Operation PanelPrecautions Printer SetupProcedure before Operation Assembling the Supply Holder Frame Assembling the AccessoriesConnecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Disassembling the Supply Holder Unit Installing the Media onto the Supply Holder UnitInstalling the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Below PrinterSetting the Feed Gap Sensor Setting Sensor PositionsSetting the Black Mark Sensor Loading the Ribbon COM Inserting the Optional Pcmcia CardsTest Print At the same time Test Print Overview Operating Modes Printer OperationOperating Modes System Requirements Installing the Printer DriversDriver Download SystemEO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Print to the following Details TabPrint using ∙ Click Capture Printer Port Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Stock Tab Stock Tab Sensor Select Stock Tab Options tab, the following display screen will appear Options TabTesting Tab Testing Tab Testing Tab Testing Tab About Tab About Tab Operation Panel On Line ModeOperation Reset Restart key Dump ModeReceive buffer size Print ConditionsCleaning MaintenancePrint Head/Platen/ Sensors Care/Handling of the Media and Ribbon Error Messages TroubleshootingError Messages Problems/Causes Solutions Error Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Removing Jammed Media „Threshold setting procedure Threshold SettingFeed key A1.1 Printer Appendix 1 SpecificationsModel 852-TS12-QQ A1.3 Media A1.2 OptionsA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorA1.4 Ribbon Appendix 2 Messages and Leds Symbols in the messageFollowing message appears „Interface Cables Appendix 3 InterfaceA4.1 Operation Panel Appendix 4 System ModeA4.2 Overview If the power is turn on whilePrinting mode selection A4.3 Self-Diagnostic TestMaintenance counter/parameter settings print out Print head element check Self-Diagnostic Test and the result print outA4.4 Printer Parameter Fine Adjustment Restart Feed Feed Length Fine AdjustmentCut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Rewind Motor Feed Motor Ribbon Motor Voltage Fine Adjustment Feed/Rewind MotorThreshold Manual Fine Adjustment Black Mark/Feed Gap Sensor A4.4 Printer Parameter Fine Adjustment ContBlack Mark Sensor Feed Gap SensorA4.5 Test Print Print Condition SettingTest Pattern Selection Specifying the Print Condition for the Test Print Issue Count SettingPrinting Mode Selection Print Speed SettingSensor Type Selection Label Length Setting Issue Mode SelectionPaper Feed Selection Pause key Test Print Pattern SelectionSlant Line 1 dot Slant Line 3 dotsBarcode CharactersNon-Printing Factory TestAuto Print A4.6 PCL Emulation SettingPrint Speed Emulation ON/OFF SelectionSensor Type Selection Media Width Setting Issue Mode SelectionMedia Size Selection Media Length Setting A4.7 Additional Information A4.7.1 Self-Diagnostic Test Result Sample and DescriptionsSdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD Letter A4.7.3 Magnified Views of Slant Line PatternAppendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full AsciiKIX Code MaxiCode UPC-A+2 digits UPC-A+5 digitsBar code GlossariesPre-printed media Index Index Page