Toshiba B-852-TS12-QQ owner manual Regional Settings Tab

Page 43

3. PRINTER OPERATION

EO1-33029

3.4 Using the B-852 Printer Properties Menus

3.4.4Regional Settings Tab (Cont.)

NOTES:

∙If displaying the driver in a language other than the system default is desired, choose the language here. Changes to the language will not take effect until the dialog is closed and opened again.

∙For a language to list here, there must be a driver translation in that language and it must be supported by the current operating system. Languages requiring double- byte character sets, such as Japanese or Chinese, may not be available unless running under the corresponding version of Windows.

Language Selection - By clicking on the arrow in the Language: scrolling text box, the following screen will appear to allow selection of the desired language to be used in the printer driver property screens.

NOTES:

∙It is possible to specify a value in another system of measurement by typing the desired units after the name. For example, if the driver is set to inches, simply type “3.5 cm” into any edit control and it will be automatically converted into “1.38 in”.

∙The “Use System Default” selection will use the system of measurement that is currently selected in Windows Control Panel’s Regional Settings.

Measurement System Selection - By clicking on the arrow in the Units: scrolling text box, the following screen will appear to allow the selection of the desired units of measurement.

3-16

Image 43

Contents 852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents A4-1 A1-1A2-1 A3-1Product Overview Introduction FeaturesUnpacking Accessories Appearance DimensionsFront View Rear View Interior Operation PanelPrecautions Printer SetupProcedure before Operation Assembling the Supply Holder Frame Assembling the AccessoriesConnecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Disassembling the Supply Holder Unit Installing the Media onto the Supply Holder UnitInstalling the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Below PrinterSetting the Feed Gap Sensor Setting Sensor PositionsSetting the Black Mark Sensor Loading the Ribbon COM Inserting the Optional Pcmcia CardsTest Print At the same time Test Print Overview Operating Modes Printer OperationOperating Modes System Installing the Printer DriversSystem Requirements Driver DownloadEO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Print to the following Details TabPrint using ∙ Click Capture Printer Port Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Stock Tab Stock Tab Sensor Select Stock Tab Options tab, the following display screen will appear Options TabTesting Tab Testing Tab Testing Tab Testing Tab About Tab About Tab Operation Panel On Line ModeOperation Reset Restart key Dump ModeReceive buffer size Print ConditionsCleaning MaintenancePrint Head/Platen/ Sensors Care/Handling of the Media and Ribbon Error Messages TroubleshootingError Messages Problems/Causes Solutions Error Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Removing Jammed Media „Threshold setting procedure Threshold SettingFeed key A1.1 Printer Appendix 1 SpecificationsModel 852-TS12-QQ Label A1.2 OptionsA1.3 Media A1.3.1 Media TypeA1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective SensorA1.4 Ribbon Appendix 2 Messages and Leds Symbols in the messageFollowing message appears „Interface Cables Appendix 3 InterfaceA4.1 Operation Panel Appendix 4 System ModeA4.2 Overview If the power is turn on whilePrinting mode selection A4.3 Self-Diagnostic TestMaintenance counter/parameter settings print out Print head element check Self-Diagnostic Test and the result print outA4.4 Printer Parameter Fine Adjustment Restart Feed Feed Length Fine AdjustmentCut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Rewind Motor Feed Motor Ribbon Motor Voltage Fine Adjustment Feed/Rewind MotorFeed Gap Sensor A4.4 Printer Parameter Fine Adjustment ContThreshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Black Mark SensorA4.5 Test Print Print Condition SettingTest Pattern Selection Specifying the Print Condition for the Test Print Issue Count SettingPrinting Mode Selection Print Speed SettingSensor Type Selection Label Length Setting Issue Mode SelectionPaper Feed Selection Slant Line 3 dots Test Print Pattern SelectionPause key Slant Line 1 dotFactory Test CharactersBarcode Non-PrintingAuto Print A4.6 PCL Emulation SettingPrint Speed Emulation ON/OFF SelectionSensor Type Selection Media Width Setting Issue Mode SelectionMedia Size Selection Media Length Setting A4.7 Additional Information A4.7.1 Self-Diagnostic Test Result Sample and DescriptionsSdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD Letter A4.7.3 Magnified Views of Slant Line PatternAppendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full AsciiKIX Code MaxiCode UPC-A+2 digits UPC-A+5 digitsBar code GlossariesPre-printed media Index Index Page