Toshiba B-852-TS12-QQ owner manual Back Feed Length Fine Adjustment

Page 86

APPENDIX 4 SYSTEM MODE

EO1-33029

A4.4 Printer Parameter Fine Adjustment

A4.4 Printer Parameter Fine Adjustment (Cont.)

Back Feed Length Fine Adjustment (Example)

Back Feed Length Fine Adjustment

With this parameter you can fine adjust the Back Feed Length. When “<3>ADJUST SET” appears, press the [PAUSE] key 3 times.

%$&.$'-PP

[RESTART]

[FEED]

%$&.$'-PP %$&.$'-PP

%$&.$'-PP

%$&.$'-PP %$&.$'-PP

NOTE:

The fine adjustment value equals the sum of the fine adjustment values set by the PC command and this parameter.

The maximum back feed lengthfine adjustment value is ±9.5mm. When the value reaches the maximum, the value remains unchanged even if the subsequent fine adjustment is performed.

[FEED] key: Pressing the [FEED] key one time causes a –0.5mm change, up to –9.5 mm.

[RESTART] key: Pressing the [RESTART] key one time causes a +0.5mm change, up to +9.5 mm.

After completing the fine adjustment, press the [PAUSE] key.

A4- 8

Image 86

Contents 852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents A3-1 A1-1A2-1 A4-1Unpacking Introduction FeaturesProduct Overview Accessories Front View Rear View DimensionsAppearance Operation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Assembling the Accessories Assembling the Supply Holder FrameConnecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Installing the Media onto the Supply Holder Unit Disassembling the Supply Holder UnitInstalling the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Printer BelowSetting the Black Mark Sensor Setting Sensor PositionsSetting the Feed Gap Sensor Loading the Ribbon Inserting the Optional Pcmcia Cards COMTest Print At the same time Test Print Printer Operation Overview Operating ModesOperating Modes Driver Download Installing the Printer DriversSystem Requirements SystemEO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Details Tab Print to the followingPrint using ∙ Click Capture Printer Port Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Stock Tab Stock Tab Sensor Select Stock Tab Options Tab Options tab, the following display screen will appearTesting Tab Testing Tab Testing Tab Testing Tab About Tab About Tab On Line Mode Operation PanelOperation Reset Dump Mode Restart keyPrint Conditions Receive buffer sizePrint Head/Platen/ Sensors MaintenanceCleaning Care/Handling of the Media and Ribbon Error Messages Problems/Causes Solutions TroubleshootingError Messages Possible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Removing Jammed Media Feed key Threshold Setting„Threshold setting procedure Model 852-TS12-QQ Appendix 1 SpecificationsA1.1 Printer A1.3.1 Media Type A1.2 OptionsA1.3 Media LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and LedsFollowing message appears Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelIf the power is turn on while A4.2 OverviewMaintenance counter/parameter settings print out A4.3 Self-Diagnostic TestPrinting mode selection Self-Diagnostic Test and the result print out Print head element checkA4.4 Printer Parameter Fine Adjustment Feed Length Fine Adjustment Restart FeedCut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Rewind Motor Feed MotorBlack Mark Sensor A4.4 Printer Parameter Fine Adjustment ContThreshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Feed Gap SensorTest Pattern Selection Print Condition SettingA4.5 Test Print Issue Count Setting Specifying the Print Condition for the Test PrintSensor Type Selection Print Speed SettingPrinting Mode Selection Paper Feed Selection Issue Mode SelectionLabel Length Setting Slant Line 1 dot Test Print Pattern SelectionPause key Slant Line 3 dotsNon-Printing CharactersBarcode Factory TestA4.6 PCL Emulation Setting Auto PrintSensor Type Selection Emulation ON/OFF SelectionPrint Speed Media Size Selection Issue Mode SelectionMedia Width Setting Media Length Setting A4.7.1 Self-Diagnostic Test Result Sample and Descriptions A4.7 Additional InformationSdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD A4.7.3 Magnified Views of Slant Line Pattern LetterAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Bar codePre-printed media Index Index Page