Toshiba B-852-TS12-QQ owner manual Stock Tab

Page 52

3. PRINTER OPERATION

EO1-33029

3.4 Using the B-852 Printer Properties Menus

3.4.8 Stock Tab (Cont.)

NOTE:

The status of this setting in the printer affects the print head temperature. Accordingly, the setting must agree with the label stock that is being used in order to ensure maximum print quality.

Print Method - The following screen display shows what appears when the arrow of the Print Method: scrolling text box has been clicked on.

Direct Thermal - Select this option when printing on thermal labels or tags without the use of a ribbon.

Thermal Transfer - Select this option when printing with a ribbon.

Sensor Select - The following screen display shows what appears when the arrow of the Sensor: scrolling text box has been clicked on.

3-25

Image 52

Contents 852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents A1-1 A2-1A3-1 A4-1Product Overview Introduction FeaturesUnpacking Accessories Appearance DimensionsFront View Rear View Operation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Assembling the Accessories Assembling the Supply Holder FrameConnecting the Cables to Your Printer Connecting the Power Cord Turning on the Printer Turning the PrinterTurning OFF the Printer Installing the Media onto the Supply Holder Unit Disassembling the Supply Holder UnitInstalling the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Printer BelowSetting the Feed Gap Sensor Setting Sensor PositionsSetting the Black Mark Sensor Loading the Ribbon Inserting the Optional Pcmcia Cards COMTest Print At the same time Test Print Printer Operation Overview Operating ModesOperating Modes Installing the Printer Drivers System RequirementsDriver Download SystemEO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Details Tab Print to the followingPrint using ∙ Click Capture Printer Port Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Stock Tab Stock Tab Sensor Select Stock Tab Options Tab Options tab, the following display screen will appearTesting Tab Testing Tab Testing Tab Testing Tab About Tab About Tab On Line Mode Operation PanelOperation Reset Dump Mode Restart keyPrint Conditions Receive buffer sizeCleaning MaintenancePrint Head/Platen/ Sensors Care/Handling of the Media and Ribbon Error Messages TroubleshootingError Messages Problems/Causes Solutions Error Messages Problems/Cause Solutions Possible ProblemsPossible Problems Causes Solutions Removing Jammed Media „Threshold setting procedure Threshold SettingFeed key A1.1 Printer Appendix 1 SpecificationsModel 852-TS12-QQ A1.2 Options A1.3 MediaA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and LedsFollowing message appears Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelIf the power is turn on while A4.2 OverviewPrinting mode selection A4.3 Self-Diagnostic TestMaintenance counter/parameter settings print out Self-Diagnostic Test and the result print out Print head element checkA4.4 Printer Parameter Fine Adjustment Feed Length Fine Adjustment Restart FeedCut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Rewind Motor Feed MotorA4.4 Printer Parameter Fine Adjustment Cont Threshold Manual Fine Adjustment Black Mark/Feed Gap SensorBlack Mark Sensor Feed Gap SensorA4.5 Test Print Print Condition SettingTest Pattern Selection Issue Count Setting Specifying the Print Condition for the Test PrintPrinting Mode Selection Print Speed SettingSensor Type Selection Label Length Setting Issue Mode SelectionPaper Feed Selection Test Print Pattern Selection Pause keySlant Line 1 dot Slant Line 3 dotsCharacters BarcodeNon-Printing Factory TestA4.6 PCL Emulation Setting Auto PrintPrint Speed Emulation ON/OFF SelectionSensor Type Selection Media Width Setting Issue Mode SelectionMedia Size Selection Media Length Setting A4.7.1 Self-Diagnostic Test Result Sample and Descriptions A4.7 Additional InformationSdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD A4.7.3 Magnified Views of Slant Line Pattern LetterAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Bar codePre-printed media Index Index Page