Toshiba B-852-TS12-QQ owner manual A1.2 Options, A1.3 Media, A1.3.1 Media Type, Label, Tag paper

Page 72

APPENDIX 1 SPECIFICATIONS

EO1-33029

A1.2 Options

A1.2 Options

Option Name	Type	Description	Source
Cutter module	B-7208-QM	A stop and cut swing cutter.	See NOTE.
PCL5 interface board	B-7708-PCL-QM	This board enables the B-852 printer to support the	See NOTE.
		HP-PCL5.
Expansion I/O	B-8700-IO-QM	Installing this board in the printer will allow a	See NOTE.
interface board		connection with an external device with the
		exclusive interface, such as the keyboard module.
Keyboard module	KB-80-QM	This module is an external intelligent keyboard unit,	See NOTE.
		including a 16 digit by 2 line LCD and 28 key
		switches.
PCMCIA interface	B-7708-PC-QM	This board enables the use of the following	See NOTE.
board		PCMCIA cards:
		LAN card: 3 COM EtherLink® III (recommended)
		ATA card: Conforming to PC card ATA standard
		Flash memory card: 4MB card (See page 2-14.)

NOTE:

Available from your nearest TOSHIBA TEC representative or TOSHIBA TEC Head Quarters.

A1.3 Media

Please make sure that the media that will be used is approved by TOSHIBA TEC. The warranty does not apply when a problem is caused by using media that is not approved by TOSHIBA TEC.

For information regarding TOSHIBA TEC-approved media, please contact a TOSHIBA TEC authorized service representative.

A1.3.1 Media Type

Two types of media can be loaded for this thermal transfer/direct thermal printer-label or tag. The table below shows size and shape of the media available for this printer.

Black Mark

Black Mark

Label

(on reverse side) Refer to

NOTE 3 below.

Tag paper

(on reverse side)

Stop

Stop

position

i

position

i

Cut position

f	g
j	Cut position

c

c

d

h	h
	h
e	e
	e
	Feed Direction

A1- 2

Image 72

Contents 852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents A1-1 A2-1A3-1 A4-1Introduction Features Product OverviewUnpacking Accessories Dimensions AppearanceFront View Rear View Operation Panel InteriorPrinter Setup PrecautionsProcedure before Operation Assembling the Accessories Assembling the Supply Holder FrameConnecting the Cables to Your Printer Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Installing the Media onto the Supply Holder Unit Disassembling the Supply Holder UnitInstalling the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Printer BelowSetting Sensor Positions Setting the Feed Gap SensorSetting the Black Mark Sensor Loading the Ribbon Inserting the Optional Pcmcia Cards COMTest Print At the same time Test Print Printer Operation Overview Operating ModesOperating Modes Installing the Printer Drivers System RequirementsDriver Download SystemEO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Details Tab Print to the followingPrint using ∙ Click Capture Printer Port Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Stock Tab Stock Tab Sensor Select Stock Tab Options Tab Options tab, the following display screen will appearTesting Tab Testing Tab Testing Tab Testing Tab About Tab About Tab On Line Mode Operation PanelOperation Reset Dump Mode Restart keyPrint Conditions Receive buffer sizeMaintenance CleaningPrint Head/Platen/ Sensors Care/Handling of the Media and Ribbon Troubleshooting Error MessagesError Messages Problems/Causes Solutions Possible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Removing Jammed Media Threshold Setting „Threshold setting procedureFeed key Appendix 1 Specifications A1.1 PrinterModel 852-TS12-QQ A1.2 Options A1.3 MediaA1.3.1 Media Type LabelA1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print AreaA1.4 Ribbon Symbols in the message Appendix 2 Messages and LedsFollowing message appears Appendix 3 Interface „Interface CablesAppendix 4 System Mode A4.1 Operation PanelIf the power is turn on while A4.2 OverviewA4.3 Self-Diagnostic Test Printing mode selectionMaintenance counter/parameter settings print out Self-Diagnostic Test and the result print out Print head element checkA4.4 Printer Parameter Fine Adjustment Feed Length Fine Adjustment Restart FeedCut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Rewind Motor Feed MotorA4.4 Printer Parameter Fine Adjustment Cont Threshold Manual Fine Adjustment Black Mark/Feed Gap SensorBlack Mark Sensor Feed Gap SensorPrint Condition Setting A4.5 Test PrintTest Pattern Selection Issue Count Setting Specifying the Print Condition for the Test PrintPrint Speed Setting Printing Mode SelectionSensor Type Selection Issue Mode Selection Label Length SettingPaper Feed Selection Test Print Pattern Selection Pause keySlant Line 1 dot Slant Line 3 dotsCharacters BarcodeNon-Printing Factory TestA4.6 PCL Emulation Setting Auto PrintEmulation ON/OFF Selection Print SpeedSensor Type Selection Issue Mode Selection Media Width SettingMedia Size Selection Media Length Setting A4.7.1 Self-Diagnostic Test Result Sample and Descriptions A4.7 Additional InformationSdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD A4.7.3 Magnified Views of Slant Line Pattern LetterAppendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digitsUPC-A+2 digits UPC-A+5 digits KIX Code MaxiCodeGlossaries Bar codePre-printed media Index Index Page