Toshiba e-STUDIO161 manual Parallel connector, Document feeder tray when the ADF is installed

Page 15

BEFORE USING THE MACHINE

Parallel connector

Connect to your computer to use the printer function. (Printer Driver Setup Guide)

Document feeder tray (when the ADF is installed)

Place the original(s) that you wish to scan face up here. Holds up to 40 originals.

Original guides (when the ADF is installed) Adjust to the size of the originals.

Feeding roller cover (when the ADF is installed)

Open to remove misfed originals. (p.47)

1

Roller rotating knob

Turn to remove misfed paper. (p.47, p.48)

Fusing unit release levers

To remove a paper misfeed from the fusing unit, push down on these levers and remove the paper. (p.50)

The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or injury.

Right side cover (when the ADF is installed)

Open to remove misfed originals. (p.47)

Exit area (when the ADF is installed)

Originals exit the machine here after copying.

Toner cartridge lock release lever

To replace the toner cartridge, pull out the toner cartridge while pushing on this lever.

Toner cartridge

Contains toner. (p.54)

Photoconductive drum

Copy images are formed on the photoconductive drum.

Fusing unit paper guide

Open to remove misfed paper.

The model name can be seen on the

Note	machines front cover.

9

Image 15

Contents Page Page Checks Passports Driver’s licenses User safety Page Disclaimer Notice Contents Peripheral Devices and Supplies Or heater Important Points When Selecting AN Installation SiteDo not install your machine in areas that are Near an air conditionerFor servicing and proper ventilation Environmental InformationTrademark acknowledgements Be sure to allow the required space around the machineADF Using the ManualMeaning of R in Original and Paper Size Indications Conventions Used in this Manual AB series metric and inch series references Main Features Part Names and Functions Exit area when the ADF is installed Parallel connectorDocument feeder tray when the ADF is installed Fusing unit release leversOperation Panel Paper feed location / misfeed location indicators Reset keyOn Line key / indicator Paper Size indicatorsPower on and OFF Power onPower OFF Special papers Paper tray type Paper type Size Weight CapacityLoading Paper PaperFan the paper Loading PaperLoading the paper tray Locks in placeSet the paper guides to the copy paper width Important points when inserting paper in the bypass trayLoading the bypass tray Unfold the bypass trayEnvelopes Changing a TRAY’S Paper Size SettingFollow these steps to change a tray’s paper size setting Indicator of the selected paper size lights upPress the Start key and then Paper Size Enter key Important points when using the printer modeCopy is delivered to the paper output tray Normal CopyingCopying from the document glass Close the document cover/ADFSet the number of copies Copying from the ADFCopying books or originals with folds or creases Auto paper select mode Two-tray model onlyStream feeding mode Removing the document coverOriginal types Auto tray switching Two-tray model onlyMaking a Copy Darker or Lighter Selecting the TrayAutomatic Ratio Selection Setting the Number of CopiesImportant note when making a large number of copies REDUCTION/ENLARGEMENT/ZOOMManual Ratio Selection Press the Auto Image keyCopy will be delivered to the paper output tray XY Zoom copying Press the Copy ratio display keySelected ratio for the vertical direction will be entered Selected ratio for the horizontal direction will Vertically-oriented original TWO-SIDED Copying Using the Bypass TrayCopy original a Place original B as shown belowPress the Dual page Copy key Copy indicator Is litDual page Copying Set the original size to A3 LDReplace the previous originals and press the Start key Interrupting a Copy RUNPress the Interrupt key to Interrupt the copy runMaketray. sure that paper is loaded Using the Printer ModeBasic Procedure for Printing Important points when setting the paper sizeOperation in Copy and Printer Modes Pausing a print jobWhen Use close paper size is disabled When Use close paper size is enabledAuto indicator stops blinking and lights steadily Adjusting the Automatic Exposure LevelMake sure that the ADF indicator is lit Exposure level indicators show the current settingPhoto indicator stops blinking and lights steadily Toner Save Mode and High Image Quality ModeMin Customising SettingsUser Programs 60 secCopies 300 dpiMinimum Long beepBase settings Selecting a Setting for a User ProgramReset single account Settings for Auditing ModeAuditing Mode Auditing Mode SettingsFor the setting codes, see Auditing Mode Settings p.36 Selecting Auditing Mode SettingsAccount number deletion Auditing modeAccount number entry Account number changeCopying when Auditing mode is enabled Resetting accountMachine does not print. on Line indicator Does not blink TroubleshootingThis chapter describes troubleshooting and misfeed removal Any one of the alarm indicatorsFront cover or the side cover is not completely closed Power switch OFFPower Save indicator is blinking Paper is outside of the specified size and weight RangePieces of paper inside machine Problem Cause and solution Misfeed occursWhen the ADF is installed Paper is not loaded properlyCopying or printing is performed Any other indicators are litOriginal smudged or blotchy Copies Transfer charger is dirtyPrinting Problems Removing the software Click the start button, and then click Control PanelClick Add or Remove Programs Indicators and Display Messages Section a Misfeed RemovalMisfeed in the ADF Remove the misfed originalMisfeed indicator will go out Misfeed in the Bypass TraySection C Misfeed in the paper feed area Misfeed in the MachineMisfed paper during Misfeed in the fusing areaLower the fusing unit release levers to Allow easier removalBe careful not to tear Misfed paper during Removal Misfeed in the transport areaClose the side cover Be careful not to tear the misfed paper during removalMisfeed in the Upper Paper Tray Close the upper paper trayPush the upper paper tray in completely Close the lower paper tray Open the lower side coverRemove the misfed paper Close the lower side coverClose the front cover Replacing the Toner CartridgeTotal copy count Checking the Total Output Count and Toner LevelChecking the Total Output Count Total output countRoutine Maintenance Cleaning the Document Glass and ADF/ Document CoverCleaning the Bypass Tray Paper Feed Roller Cleaning the Transfer Charger Specifications Peripheral DevicesAutomatic Document Feeder Sheet Paper Feed Unit Part names SpecificationSpecifications Printer Function Software License Page Index Original types Setting the number of copiesTray Select key 11, 15, 16, 18, 19, 21 Troubleshooting Two-sided copying using the bypass trayOriginal, placing Machine settingsProblem occurs Indicators, lit and blinkingMemo Page DP-1620 OME030059A0