Toshiba e-STUDIO161 manual Power on and OFF, Power OFF

Page 18

POWER ON AND OFF

The power switch is located on the left side of the machine.

POWER ON

Turn the power switch to the "ON" position.

It will take about 45 seconds for the machine to warm up. While the machine is warming up, the POWER SAVE

indicator (

) will blink.

(The POWER SAVE

indicator (

) will go off

when the machine is ready to copy.)

However, you can make desired settings and press the [START] key ( ) during warm-up. Copying will start after warm-up.

POWER OFF

Make sure that the machine is not in operation and then turn the power switch to the "OFF" position.

If the power switch is turned off while the machine is in operation, a misfeed may occur and the job that was in progress will be cancelled.

Check the following to

make sure the machine is not in operation:

• The START indicator is lit. (Initial state)

• The POWER SAVE indicator ( ) is lit. ("Preheat mode" or "Auto power shut-off" mode)

•The machine reverts to the initial settings when it is first turned on, when the [RESET] key () is pressed, Note or when no keys are pressed for the preset "Auto clear" time following the end of a copy job. When the

machine reverts to the initial settings, all settings and functions selected to that point are cancelled. The "Auto clear" time can be changed in the user settings. (p.33)

•The machine is initially set to automatically enter power save mode if not used for copying or printing, for a preset period of time. This setting can be changed in the user programs. (p.33)

Power Save Modes

The machine has two power save modes to reduce overall power consumption thereby reducing the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are "Preheat mode" and "Auto power shut-off mode".

Preheat mode

This function automatically switches the machine to a low power consumption state if the set duration of time elapses without the machine being used when the power is on. The POWER SAVE indicator ( ) lights up, however, the keys on the operation panel can be used. Normal operation automatically resumes when a key on the operation panel is pressed, an original is placed, or a print job is received.

Auto power shut-off mode

This function automatically switches the machine to a state that consumes even less power than preheat mode if the set duration of time elapses without the machine being used when the power is on. All lights except the POWER SAVE indicator ( ) and ON LINE indicator ( ) go off. To resume normal operation, press the [START] key ( ). Normal operation also resumes automatically when a print job is received. While in auto power shut-off mode, no keys (except the [START] key ()) can be used.

• The preheat activation time and the "Auto power shut-off timer" can be changed using user programs. It is

Note

suggested that you set times that are appropriate for your usage of the machine. (p.33)

 

Initial settings

The machine assumes the initial settings when it is first turned on, when the [RESET] key (

) is pressed, and

approximately one minute after the last copy is made in any mode.

 

Copy ratio: 100%, Exposure: Automatic

 

Copy quantity: 0, All special copier modes: Off

Auto paper selection: On, Paper feed station: The tray selected in the "Default tray setting" in the user programs. (p.33)

12

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Page Page Checks Passports Driver’s licenses User safety Page Disclaimer Notice Contents Peripheral Devices and Supplies Near an air conditioner Important Points When Selecting AN Installation SiteDo not install your machine in areas that are Or heaterBe sure to allow the required space around the machine Environmental InformationTrademark acknowledgements For servicing and proper ventilationConventions Used in this Manual Using the ManualMeaning of R in Original and Paper Size Indications ADFAB series metric and inch series references Main Features Part Names and Functions Fusing unit release levers Parallel connectorDocument feeder tray when the ADF is installed Exit area when the ADF is installedOperation Panel Paper Size indicators Reset keyOn Line key / indicator Paper feed location / misfeed location indicatorsPower on and OFF Power onPower OFF Paper Paper tray type Paper type Size Weight CapacityLoading Paper Special papersLocks in place Loading PaperLoading the paper tray Fan the paperUnfold the bypass tray Important points when inserting paper in the bypass trayLoading the bypass tray Set the paper guides to the copy paper widthIndicator of the selected paper size lights up Changing a TRAY’S Paper Size SettingFollow these steps to change a tray’s paper size setting EnvelopesImportant points when using the printer mode Press the Start key and then Paper Size Enter keyClose the document cover/ADF Normal CopyingCopying from the document glass Copy is delivered to the paper output trayCopying from the ADF Set the number of copiesRemoving the document cover Auto paper select mode Two-tray model onlyStream feeding mode Copying books or originals with folds or creasesSelecting the Tray Auto tray switching Two-tray model onlyMaking a Copy Darker or Lighter Original typesREDUCTION/ENLARGEMENT/ZOOM Setting the Number of CopiesImportant note when making a large number of copies Automatic Ratio SelectionManual Ratio Selection Press the Auto Image keyCopy will be delivered to the paper output tray XY Zoom copying Press the Copy ratio display keySelected ratio for the vertical direction will be entered Selected ratio for the horizontal direction will Place original B as shown below TWO-SIDED Copying Using the Bypass TrayCopy original a Vertically-oriented originalSet the original size to A3 LD Copy indicator Is litDual page Copying Press the Dual page Copy keyInterrupt the copy run Interrupting a Copy RUNPress the Interrupt key to Replace the previous originals and press the Start keyImportant points when setting the paper size Using the Printer ModeBasic Procedure for Printing Maketray. sure that paper is loadedWhen Use close paper size is enabled Pausing a print jobWhen Use close paper size is disabled Operation in Copy and Printer ModesExposure level indicators show the current setting Adjusting the Automatic Exposure LevelMake sure that the ADF indicator is lit Auto indicator stops blinking and lights steadilyToner Save Mode and High Image Quality Mode Photo indicator stops blinking and lights steadily60 sec Customising SettingsUser Programs MinLong beep 300 dpiMinimum CopiesSelecting a Setting for a User Program Base settingsAuditing Mode Settings Settings for Auditing ModeAuditing Mode Reset single accountSelecting Auditing Mode Settings For the setting codes, see Auditing Mode Settings p.36Account number change Auditing modeAccount number entry Account number deletionResetting account Copying when Auditing mode is enabledAny one of the alarm indicators TroubleshootingThis chapter describes troubleshooting and misfeed removal Machine does not print. on Line indicator Does not blinkPaper is outside of the specified size and weight Range Power switch OFFPower Save indicator is blinking Front cover or the side cover is not completely closedPaper is not loaded properly Problem Cause and solution Misfeed occursWhen the ADF is installed Pieces of paper inside machineCopies Transfer charger is dirty Any other indicators are litOriginal smudged or blotchy Copying or printing is performedPrinting Problems Removing the software Click the start button, and then click Control PanelClick Add or Remove Programs Indicators and Display Messages Remove the misfed original Misfeed RemovalMisfeed in the ADF Section aMisfeed indicator will go out Misfeed in the Bypass TraySection C Misfeed in the Machine Misfeed in the paper feed areaAllow easier removal Misfeed in the fusing areaLower the fusing unit release levers to Misfed paper duringBe careful not to tear the misfed paper during removal Misfeed in the transport areaClose the side cover Be careful not to tear Misfed paper during RemovalMisfeed in the Upper Paper Tray Close the upper paper trayPush the upper paper tray in completely Close the lower side cover Open the lower side coverRemove the misfed paper Close the lower paper trayReplacing the Toner Cartridge Close the front coverTotal output count Checking the Total Output Count and Toner LevelChecking the Total Output Count Total copy countRoutine Maintenance Cleaning the Document Glass and ADF/ Document CoverCleaning the Bypass Tray Paper Feed Roller Cleaning the Transfer Charger Specifications Peripheral DevicesAutomatic Document Feeder Part names Specification Sheet Paper Feed UnitSpecifications Printer Function Software License Page Index Two-sided copying using the bypass tray Setting the number of copiesTray Select key 11, 15, 16, 18, 19, 21 Troubleshooting Original typesIndicators, lit and blinking Machine settingsProblem occurs Original, placingMemo Page DP-1620 OME030059A0

e-STUDIO161 specifications

The Toshiba e-STUDIO161 is a multifunctional display of efficiency and reliability, designed to cater to the needs of small to medium-sized businesses. This compact copier-printer offers various features that make it an ideal choice for organizations looking to streamline their document workflow while maintaining high-quality output.

One of the standout qualities of the e-STUDIO161 is its versatility. This machine not only functions as a copier but also provides printing and scanning capabilities, making it a comprehensive office device. It operates with a print speed of up to 16 pages per minute, ensuring that users do not experience unnecessary downtime during busy workloads. The device also has a first copy output time of approximately 8.5 seconds, which highlights its efficiency for quick copying tasks.

In terms of technology, the e-STUDIO161 employs advanced digital imaging technology that guarantees sharp, clear prints and copies. The machine supports a maximum resolution of 600 x 600 dpi, delivering high-quality outputs for documents and images. Moreover, the printing engine is designed for easy operation, allowing users to navigate the settings with an intuitive control panel.

Another notable feature is its document feeding system. The Toshiba e-STUDIO161 is equipped with a 50-sheet automatic document feeder (ADF), which enhances productivity by allowing users to scan or copy multiple pages without manual intervention. The scanner supports color scanning with a resolution of 600 x 600 dpi, enabling high-quality digital archiving and document distribution.

Environmental consciousness is a critical aspect of the e-STUDIO161's design. It is Energy Star certified, which means it meets stringent energy efficiency standards. The device also features a sleep mode to minimize power consumption during inactivity, making it a suitable choice for businesses that prioritize sustainability.

The e-STUDIO161 has a compact size, allowing it to fit comfortably in limited office space. It is designed for easy installation and setup, with straightforward connectivity options that include USB and network capabilities. This facilitates seamless integration into existing office networks, ensuring that users can print and scan with minimal hassle.

In summary, the Toshiba e-STUDIO161 is a multifunctional device that brings together speed, quality, and efficiency. Its advanced imaging technology, versatile features, and compact design make it a valuable asset for any office, providing a perfect solution to meet diverse document management needs. With a focus on user-friendliness and environmental sustainability, the e-STUDIO161 stands out as a reliable choice for modern businesses.
Top Page Image Contents