Toshiba e-STUDIO161 manual Loading Paper, Special papers

Page 19

LOADING PAPER

The paper required indicator ( ) will light up when there is no copy paper in the selected paper feed tray, or when the selected paper tray is not installed or is improperly installed.

PAPER

For best results, use only TOSHIBA recommended paper.

Paper tray type	Paper type	Size	Weight	Capacity
Paper tray	Standard paper	A5*1	56 g/m2 to 90 g/m2 *2	250 sheets
	Recycled paper	A4	(15 lbs. to 24 lbs. *2)	(Load paper lower than
		B4		the line on the tray)
		A3
		ST*1
		LT
		8-1/2" x 13"
		LD
Bypass tray	Standard paper	A6R to A3	56 g/m2 to 80 g/m2	100 sheets *3
	Recycled paper	(ST to LD)	(15 lbs. to 20 lbs.)
	Thick paper		Max. 200 g/m2 (54 lbs.)	Load one sheet of
				these papers at a time
	Transparency film			these papers at a time
	Transparency film			to the bypass tray.
	Labels			to the bypass tray.
	Labels

	Envelopes	International DL		5 sheets
		(110 mm x 220 mm)
		International C5
		(162 mm x 229 mm)
		Commercial 9
		(3-7/8" x 8-7/8")			1
		Commercial 10
		(4-1/8" x 9-1/2")
*1A5 (ST) can be used in the upper paper tray but cannot be used in the second tray.

*2When making a large number of copies or prints using 90 g/m2 (24 lbs.) paper, remove the output from the paper output tray when about 100 pages have been printed. The output may not stack correctly if more than 100 pages are allowed to accumulate.

*3The number of sheets of the paper which can be set changes with the weight of a paper.

Special papers

Follow these guidelines when using special papers.

●Use TOSHIBA recommended transparency film and label sheets. Using other than TOSHIBA recommended paper may result in misfeeds or smudges on the output. If other than TOSHIBA recommended media must be used, feed each sheet one at a time using the bypass tray (do not attempt continuous copying or printing).

●There are many varieties of special paper available on the market, and some cannot be used with this machine. Before using special paper, contact your authorized service representative.

●Before using other than TOSHIBA recommended paper, make a test copy to see if the paper is suitable.

13

Image 19

Contents Page Page Checks Passports Driver’s licenses User safety Page Disclaimer Notice Contents Peripheral Devices and Supplies Or heater Important Points When Selecting AN Installation SiteDo not install your machine in areas that are Near an air conditionerFor servicing and proper ventilation Environmental InformationTrademark acknowledgements Be sure to allow the required space around the machineADF Using the ManualMeaning of R in Original and Paper Size Indications Conventions Used in this ManualAB series metric and inch series references Main Features Part Names and Functions Exit area when the ADF is installed Parallel connectorDocument feeder tray when the ADF is installed Fusing unit release levers Operation Panel Paper feed location / misfeed location indicators Reset keyOn Line key / indicator Paper Size indicatorsPower on Power on and OFFPower OFF Special papers Paper tray type Paper type Size Weight CapacityLoading Paper PaperFan the paper Loading PaperLoading the paper tray Locks in placeSet the paper guides to the copy paper width Important points when inserting paper in the bypass trayLoading the bypass tray Unfold the bypass trayEnvelopes Changing a TRAY’S Paper Size SettingFollow these steps to change a tray’s paper size setting Indicator of the selected paper size lights upPress the Start key and then Paper Size Enter key Important points when using the printer modeCopy is delivered to the paper output tray Normal CopyingCopying from the document glass Close the document cover/ADFSet the number of copies Copying from the ADFCopying books or originals with folds or creases Auto paper select mode Two-tray model onlyStream feeding mode Removing the document coverOriginal types Auto tray switching Two-tray model onlyMaking a Copy Darker or Lighter Selecting the TrayAutomatic Ratio Selection Setting the Number of CopiesImportant note when making a large number of copies REDUCTION/ENLARGEMENT/ZOOMPress the Auto Image key Manual Ratio SelectionCopy will be delivered to the paper output tray Press the Copy ratio display key XY Zoom copyingSelected ratio for the vertical direction will be entered Selected ratio for the horizontal direction will Vertically-oriented original TWO-SIDED Copying Using the Bypass TrayCopy original a Place original B as shown belowPress the Dual page Copy key Copy indicator Is litDual page Copying Set the original size to A3 LDReplace the previous originals and press the Start key Interrupting a Copy RUNPress the Interrupt key to Interrupt the copy runMaketray. sure that paper is loaded Using the Printer ModeBasic Procedure for Printing Important points when setting the paper sizeOperation in Copy and Printer Modes Pausing a print jobWhen Use close paper size is disabled When Use close paper size is enabledAuto indicator stops blinking and lights steadily Adjusting the Automatic Exposure LevelMake sure that the ADF indicator is lit Exposure level indicators show the current settingPhoto indicator stops blinking and lights steadily Toner Save Mode and High Image Quality ModeMin Customising SettingsUser Programs 60 secCopies 300 dpiMinimum Long beepBase settings Selecting a Setting for a User ProgramReset single account Settings for Auditing ModeAuditing Mode Auditing Mode SettingsFor the setting codes, see Auditing Mode Settings p.36 Selecting Auditing Mode SettingsAccount number deletion Auditing modeAccount number entry Account number changeCopying when Auditing mode is enabled Resetting accountMachine does not print. on Line indicator Does not blink TroubleshootingThis chapter describes troubleshooting and misfeed removal Any one of the alarm indicatorsFront cover or the side cover is not completely closed Power switch OFFPower Save indicator is blinking Paper is outside of the specified size and weight RangePieces of paper inside machine Problem Cause and solution Misfeed occursWhen the ADF is installed Paper is not loaded properlyCopying or printing is performed Any other indicators are litOriginal smudged or blotchy Copies Transfer charger is dirtyPrinting Problems Click the start button, and then click Control Panel Removing the softwareClick Add or Remove Programs Indicators and Display Messages Section a Misfeed RemovalMisfeed in the ADF Remove the misfed originalMisfeed in the Bypass Tray Misfeed indicator will go outSection C Misfeed in the paper feed area Misfeed in the MachineMisfed paper during Misfeed in the fusing areaLower the fusing unit release levers to Allow easier removalBe careful not to tear Misfed paper during Removal Misfeed in the transport areaClose the side cover Be careful not to tear the misfed paper during removalClose the upper paper tray Misfeed in the Upper Paper TrayPush the upper paper tray in completely Close the lower paper tray Open the lower side coverRemove the misfed paper Close the lower side coverClose the front cover Replacing the Toner CartridgeTotal copy count Checking the Total Output Count and Toner LevelChecking the Total Output Count Total output countCleaning the Document Glass and ADF/ Document Cover Routine MaintenanceCleaning the Bypass Tray Paper Feed Roller Cleaning the Transfer Charger Peripheral Devices SpecificationsAutomatic Document Feeder Sheet Paper Feed Unit Part names SpecificationSpecifications Printer Function Software License Page Index Original types Setting the number of copiesTray Select key 11, 15, 16, 18, 19, 21 Troubleshooting Two-sided copying using the bypass trayOriginal, placing Machine settingsProblem occurs Indicators, lit and blinkingMemo Page DP-1620 OME030059A0