Toshiba e-STUDIO161 manual Problem Cause and solution Misfeed occurs, Paper is not loaded properly

Page 48

TROUBLESHOOTING

Problem

 

 

Cause and solution

Page

 

Misfeed occurs.

 

47

 

→

To remove the misfeed, see "MISFEED REMOVAL".

 

 

 

 

 

 

The paper is outside of the specified size and weight

13

 

range.

 

 

→ Use copy paper within the specified range.

 

 

 

 

 

Paper curled or damp.

 

 

→ Do not use curled or crimped paper. Replace with dry copy paper.

–

 

 

During periods when the machine is not used for a long time,

 

 

remove the paper from the tray and store it in a dark place in a

 

 

 

bag to prevent moisture absorption.

 

 

 

 

 

Paper is not loaded properly.

14

 

→

Make sure the paper is properly installed.

 

 

 

 

 

 

Pieces of paper inside machine.

47

 

→

Remove all pieces of misfed paper.

 

 

 

 

 

Paper misfeed.

Too much paper is loaded in the tray.

 

→ If the stack of paper is higher than the indicator line on the tray,

14

 

 

 

remove some of the paper and reload so that the stack does not

 

 

 

 

 

exceed the line.

 

 

 

 

 

 

Some sheets of paper stick together.

14

 

→

Fan the paper well before loading it.

 

 

 

 

 

 

The guides on the bypass tray do not match the width of

15

 

the paper.

 

 

→ Adjust the guides to match the width of the paper.

 

 

 

 

 

The bypass tray extension is not pulled out.

15

 

→

When loading a large size of paper, pull out the extension.

 

 

 

 

 

 

The bypass paper feed roller is dirty.

57

 

→

Clean the roller.

 

 

 

 

 

 

 

 

A5 (ST) paper is loaded in lower paper tray.

13, 14

 

→ A5 (ST) size paper must be loaded in upper paper tray or the

 

 

bypass tray.

 

 

 

 

 

 

 

Original(s) curled.

 

–

 

→ The original size cannot be correctly detected if the original is

 

 

curled or folded. Straighten the original.

 

Original size not selected

 

 

The original includes any large black solid areas.

 

automatically.

→ If the original includes any large black solid areas, the original size

–

(When the ADF is installed.)

 

may not be detected automatically. Use the [ORIGINAL SIZE

 

 

 

 

ENTER] key (

) to select the paper size.

 

 

 

 

 

The machine is directly exposed to sunlight.

–

 

→

Install in a location that is not exposed to sunlight.

 

 

 

 

 

 

 

42

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Page Page Checks Passports Driver’s licenses User safety Page Disclaimer Notice Contents Peripheral Devices and Supplies Important Points When Selecting AN Installation Site Do not install your machine in areas that areNear an air conditioner Or heaterEnvironmental Information Trademark acknowledgementsBe sure to allow the required space around the machine For servicing and proper ventilationUsing the Manual Meaning of R in Original and Paper Size IndicationsConventions Used in this Manual ADFAB series metric and inch series references Main Features Part Names and Functions Parallel connector Document feeder tray when the ADF is installedFusing unit release levers Exit area when the ADF is installedOperation Panel Reset key On Line key / indicatorPaper Size indicators Paper feed location / misfeed location indicatorsPower on and OFF Power onPower OFF Paper tray type Paper type Size Weight Capacity Loading PaperPaper Special papersLoading Paper Loading the paper trayLocks in place Fan the paperImportant points when inserting paper in the bypass tray Loading the bypass trayUnfold the bypass tray Set the paper guides to the copy paper widthChanging a TRAY’S Paper Size Setting Follow these steps to change a tray’s paper size settingIndicator of the selected paper size lights up EnvelopesImportant points when using the printer mode Press the Start key and then Paper Size Enter keyNormal Copying Copying from the document glassClose the document cover/ADF Copy is delivered to the paper output trayCopying from the ADF Set the number of copiesAuto paper select mode Two-tray model only Stream feeding modeRemoving the document cover Copying books or originals with folds or creasesAuto tray switching Two-tray model only Making a Copy Darker or LighterSelecting the Tray Original typesSetting the Number of Copies Important note when making a large number of copiesREDUCTION/ENLARGEMENT/ZOOM Automatic Ratio SelectionManual Ratio Selection Press the Auto Image keyCopy will be delivered to the paper output tray XY Zoom copying Press the Copy ratio display keySelected ratio for the vertical direction will be entered Selected ratio for the horizontal direction will TWO-SIDED Copying Using the Bypass Tray Copy original aPlace original B as shown below Vertically-oriented originalCopy indicator Is lit Dual page CopyingSet the original size to A3 LD Press the Dual page Copy keyInterrupting a Copy RUN Press the Interrupt key toInterrupt the copy run Replace the previous originals and press the Start keyUsing the Printer Mode Basic Procedure for PrintingImportant points when setting the paper size Maketray. sure that paper is loadedPausing a print job When Use close paper size is disabledWhen Use close paper size is enabled Operation in Copy and Printer ModesAdjusting the Automatic Exposure Level Make sure that the ADF indicator is litExposure level indicators show the current setting Auto indicator stops blinking and lights steadilyToner Save Mode and High Image Quality Mode Photo indicator stops blinking and lights steadilyCustomising Settings User Programs60 sec Min300 dpi MinimumLong beep CopiesSelecting a Setting for a User Program Base settingsSettings for Auditing Mode Auditing ModeAuditing Mode Settings Reset single accountSelecting Auditing Mode Settings For the setting codes, see Auditing Mode Settings p.36Auditing mode Account number entryAccount number change Account number deletionResetting account Copying when Auditing mode is enabledTroubleshooting This chapter describes troubleshooting and misfeed removalAny one of the alarm indicators Machine does not print. on Line indicator Does not blinkPower switch OFF Power Save indicator is blinkingPaper is outside of the specified size and weight Range Front cover or the side cover is not completely closedProblem Cause and solution Misfeed occurs When the ADF is installedPaper is not loaded properly Pieces of paper inside machineAny other indicators are lit Original smudged or blotchyCopies Transfer charger is dirty Copying or printing is performedPrinting Problems Removing the software Click the start button, and then click Control PanelClick Add or Remove Programs Indicators and Display Messages Misfeed Removal Misfeed in the ADFRemove the misfed original Section aMisfeed indicator will go out Misfeed in the Bypass TraySection C Misfeed in the Machine Misfeed in the paper feed areaMisfeed in the fusing area Lower the fusing unit release levers toAllow easier removal Misfed paper duringMisfeed in the transport area Close the side coverBe careful not to tear the misfed paper during removal Be careful not to tear Misfed paper during RemovalMisfeed in the Upper Paper Tray Close the upper paper trayPush the upper paper tray in completely Open the lower side cover Remove the misfed paperClose the lower side cover Close the lower paper trayReplacing the Toner Cartridge Close the front coverChecking the Total Output Count and Toner Level Checking the Total Output CountTotal output count Total copy countRoutine Maintenance Cleaning the Document Glass and ADF/ Document CoverCleaning the Bypass Tray Paper Feed Roller Cleaning the Transfer Charger Specifications Peripheral DevicesAutomatic Document Feeder Part names Specification Sheet Paper Feed UnitSpecifications Printer Function Software License Page Index Setting the number of copies Tray Select key 11, 15, 16, 18, 19, 21 TroubleshootingTwo-sided copying using the bypass tray Original typesMachine settings Problem occursIndicators, lit and blinking Original, placingMemo Page DP-1620 OME030059A0

e-STUDIO161 specifications

The Toshiba e-STUDIO161 is a multifunctional display of efficiency and reliability, designed to cater to the needs of small to medium-sized businesses. This compact copier-printer offers various features that make it an ideal choice for organizations looking to streamline their document workflow while maintaining high-quality output.

One of the standout qualities of the e-STUDIO161 is its versatility. This machine not only functions as a copier but also provides printing and scanning capabilities, making it a comprehensive office device. It operates with a print speed of up to 16 pages per minute, ensuring that users do not experience unnecessary downtime during busy workloads. The device also has a first copy output time of approximately 8.5 seconds, which highlights its efficiency for quick copying tasks.

In terms of technology, the e-STUDIO161 employs advanced digital imaging technology that guarantees sharp, clear prints and copies. The machine supports a maximum resolution of 600 x 600 dpi, delivering high-quality outputs for documents and images. Moreover, the printing engine is designed for easy operation, allowing users to navigate the settings with an intuitive control panel.

Another notable feature is its document feeding system. The Toshiba e-STUDIO161 is equipped with a 50-sheet automatic document feeder (ADF), which enhances productivity by allowing users to scan or copy multiple pages without manual intervention. The scanner supports color scanning with a resolution of 600 x 600 dpi, enabling high-quality digital archiving and document distribution.

Environmental consciousness is a critical aspect of the e-STUDIO161's design. It is Energy Star certified, which means it meets stringent energy efficiency standards. The device also features a sleep mode to minimize power consumption during inactivity, making it a suitable choice for businesses that prioritize sustainability.

The e-STUDIO161 has a compact size, allowing it to fit comfortably in limited office space. It is designed for easy installation and setup, with straightforward connectivity options that include USB and network capabilities. This facilitates seamless integration into existing office networks, ensuring that users can print and scan with minimal hassle.

In summary, the Toshiba e-STUDIO161 is a multifunctional device that brings together speed, quality, and efficiency. Its advanced imaging technology, versatile features, and compact design make it a valuable asset for any office, providing a perfect solution to meet diverse document management needs. With a focus on user-friendliness and environmental sustainability, the e-STUDIO161 stands out as a reliable choice for modern businesses.
Top Page Image Contents