NETGEAR CG3000Dv2 user manual Technical Specifications, Component Specification

Page 55

NETGEAR DOCSIS 3.0 N450 Wi-Fi Data Gateway

Feature

Parameter

Default

Wireless

Wireless communication

Enabled

 

 

 

 

SSID name

Appears on the label of the gateway.

 

 

 

 

Security

WPA/WPA2

 

 

The default WPA/WPA2 password appears on the

 

 

label of the gateway.

 

 

 

 

Broadcast SSID

Enabled

 

 

 

 

Transmission speed

Auto1

 

Country/region

United States (varies by region)

 

 

 

 

RF channel

Auto

 

 

 

 

Operating mode

n, g, and b

 

 

 

 

Data rate

Best

 

 

 

 

Output power

Full

 

 

 

 

Access point

Enabled

 

 

 

 

Authentication type

Open System

 

 

 

 

Wireless Card Access List

All wireless stations allowed

 

 

 

1.Maximum wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput varies. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, might lower actual data throughput rate.

Technical Specifications

The following table describes the technical specifications for the gateway.

Table 3. Technical specifications

Component

Specification

Network protocol and

Data and routing protocols: TCP/IP, DHCP server, and client, DNS relay, NAT

standards compatibility

(many-to-one), TFTP client, VPN pass-through (IPSec, PPTP)

Power adapter

• North America (input): 120V, 60 Hz, input

 

• All regions (output): 12 V-DC @ 2.5A output 30W maximum

 

 

Physical specifications

• Dimensions: 10.2 by 6.49 by 3.65 in. (259.17 by 164.77 by 92.72 mm)

 

• Weight: 1.30 lb (590 g)

 

 

Environmental

• Operating temperature: 32° to 140°-F (0° to 40°-C)

 

• Operating humidity: 90% maximum relative humidity, non-condensing

 

• Electromagnetic emissions: Meets requirements of: FCC Part 15 Class B.

 

 

Supplemental Information

55

Image 55
Contents USA August 2013 East Plumeria Drive San Jose, CARevision History Contents Appendix a Supplemental Information Connecting to the Internet Description Gateway Front PanelSecurity, see the Use Push N Connect WPS Wireless Setup on Gateway rear panel Gateway Rear PanelLabel Wireless Performance and Gateway Location To log in to the gateway Log In to Your Gateway To view or configure basic settings View Basic SettingsConfiguring Your Wireless Network  To view or configure the wireless settings Set Up Your Wireless NetworkNetgear Docsis 3.0 N450 Wi-Fi Data Gateway Use Push N Connect WPS Wireless Setup Netgear Docsis 3.0 N450 Wi-Fi Data Gateway  To add a wireless device to your gateway using a PIN Add a Client Using a PIN To set up Wi-Fi Multimedia Set Up Wi-Fi Multimedia To change the password Change the PasswordPage Filtering Content  To receive notification of attacks by email View Denial of Service DoS Attack Logs To block access to sites containing certain words Limit Internet Site AccessClick Remove Keyword  To block access to certain domains Disable Gateway Features Allow Unrestricted Access To disable specific NAT ALG Status features  To disable specific web featuresFeature Description Netgear Docsis 3.0 N450 Wi-Fi Data Gateway Maintaining Your Network  To view the gateway status View the Gateway StatusModem field Description  To view the gateway’s initialization procedure Back Up and Restore Your SettingsView the Connection Status  To restore the backup settings  To back up the settingsView the Event Log  To view the event log Run the Diagnostic Utilities To run a ping test Click Start Test  To run a traceroute test Traceroute UtilityAdvanced Settings  To configure advanced wireless settings Advanced Wireless SettingsAdvanced Wireless Settings Description MAC Filtering  To remove a computer from the list  To stop blocking a computerIP Filtering  To set up IP filtering To delete a device from the IP Filter List Port Blocking  To configure port blockingPort Forwarding Netgear Docsis 3.0 N450 Wi-Fi Data Gateway Port Triggering  To configure port triggeringDMZ Host  To set up a DMZ hostSelect the Respond to Ping on WAN Port check box  To configure LAN IP settings LAN IP SetupClick Delete LAN SwitchReserve an IP Address for Dhcp Use  To reserve an IP address for Dhcp To configure UPnP Configure Universal Plug and Play UPnP To configure the switch ports  To disable a LAN portSet Networking Protocols  To enable NTP To remove a USB device Enable Network Address Translation To disable NAT Remove USB DevicesSee Troubleshoot a TCP/IP Network Using a Ping Utility on TroubleshootingConnect to the Gateway’s Main Menu Basic FunctionsLED Behavior Action Troubleshoot the ISP Connection Troubleshoot a TCP/IP Network Using a Ping UtilityPing Test the LAN Path to Your GatewayNetgear Docsis 3.0 N450 Wi-Fi Data Gateway Supplemental Information Feature Parameter Default Factory Default SettingsComponent Specification Technical SpecificationsNetgear Docsis 3.0 N450 Wi-Fi Data Gateway Regulatory Compliance Information Notification of ComplianceFCC Caution Avertissement