Airlink101 AR570W Ddns, Reset You can also click ‘Reset’ button unselect all, Dynamic DNS

Page 35

Reset

You can also click ‘Reset’ button unselect all.

After you finish with all settings, please click “Apply” button.

If you want to reset all settings in this page, please click “Cancel” button.

After you clicked Apply, the following message will be displayed on your web browser:

You can click “Continue” to back to previous setup page to continue on other setup procedures, or click “Apply” to reboot the router so the settings will take effect (Please wait for about 30 seconds while router is rebooting).

3.1.4 DDNS

DDNS allows you to map the static domain name to a dynamic IP address. You must get an account, password and a static domain name from a DDNS service provider. This router supports DynDNS (www.dyndns.org), and TZO (www.tzo.com).

Parameters	Default	Description
Dynamic DNS	Disable	Enable/Disable the DDNS function of this router.
		36

Image 35

Contents Wireless N 150 Router Federal Communication Commission Interference Statement Table of Contents Troubleshooting Technical Support Router Interface FeaturesPackage Contents Back Panel WPS Using EZ Setup Wizard Installing the RouterPage Page Dynamic IP Cable Modem users Page Page Congratulations! Your router configuration has been finished Connecting to the Router Wirelessly Page Using Web Configuration Utility Page Time Zone Setup WizardEnable NTP Update Current TimeMAC Address Time Server AddressDaylight Savings Host NameUser Name Primary DNSSecondary DNS Idle Time Out PasswordService Name Connection TypePptp Gateway PptpBEZEQ-ISRAEL Connection IDUser Name Please input user name assigned by Telstra L2TP GatewayParameterDescription Associated Clients Channel NumberWPA2Mixed Page 2 LAN Network1 WAN Dhcp Server IP addressSubnet Mask 802.1d Spanning TreeDhcp Client End IP Enable Static Dhcp LeasesLease Time Dhcp Client Start IPNAT / Static Routing Destination LAN IP Enable Static RoutingDefault Gateway ResetDynamic DNS Reset You can also click ‘Reset’ button unselect allDdns Account Password/KeyProvider Band WirelessBasic Settings Show Active Clients Wireless SecuritySee 3.2.2.1 to 3.2.2.3 for each encryption type Enable 802.1x AuthenticationEncryption Encryption Key 1~4 Default Tx KeyKey Length Key FormatPre-shared Key WPA Unicast Cipher SuitePre-shared Key Format Radius Server Port Radius Server PasswordMAC Control Radius Server IP AddressClear Enable MAC ControlComment Fragment Threshold Advanced SettingsDtim Period Tx PowerRTS Threshold Beacon Interval5 WPS Page Config Mode Enable WPSWi-Fi Protected Setup Information Configure by Pin Code Configure by Push ButtonVirtual Server Port Forwarding Application & GamingCurrent Virtual Server Table Special Applications Port TriggeringPublic Port Add in red box Enable Special ApplicationsTCP/UDP Port to Open Popular Application3 DMZ Current DMZ Table Enable DMZPublic IP Client PC IP addressReset You can also click ‘Reset’ button to unselect all ALG Settings5 QoS Current QoS Table Enable QoSTotal Download Bandwidth Total Upload BandwidthLocal Port Range Rule NameBandwidth Local IP AddressProtocol Deny/Allow Access RestrictionsEnable IP & Port Filtering 1 IP & Port FilteringPort Range Client ServiceClient PC Description MAC Filtering Current MAC Filtering Table Enable MAC Filtering3 URL/Keyword Filtering Client PC MAC AddressCurrent URL Blocking Table Enable URL FilteringURL/Keyword Firewall SecurityDoS Denial-of-Service Ping of Death L2TP pass through VPN Pass throughIPsec pass through Pptp pass throughTime AdministrationManagement Current PasswordNew Password Confirmed PasswordReset Reboot Remote Management Firmware Upgrade Restore to Factory Default Configuration SettingsBackup Settings Restore SettingsRefresh 6 LogSave Statistics LAN Status Wlan Wireless LAN StatusStatus Internet Connection StatusSystem Status Troubleshooting Technical Support