Campbell Hausfeld WG2044 Operation, Welding Helmet, Handshield, Assembly Promotional, Models Only

Wire Feed Arc Welder
Assembly (Continued)		4. To attach the handle, place shield on			too close to the face, use a different
		a flat surface and press handle into			hole in the adjustment arm. Adjust the
HOOKUP PROCEDURE (Continued)		place (See Figure 10).			tension nuts so that helmet can be
		NOTE: If you have never welded			easily lowered over the face by
					nodding the head.
	counterclockwise. When gas is	before or have little experience, a
		full face helmet is recommended.
	emitted from cylinder, close valve by			Operation
		Both hands are needed to stabilize
	turning clockwise. This will blow out
		and control the angle and arc
	dust or dirt that may have
		length of the torch.		1. Be sure to read,
	accumulated around valve seat.
		Welding Helmet			understand and comply
2. Install regulator onto cylinder valve.
					with all precautions in
	Tighten stem nut securely to gas	Assembly (Promotional			the General Safety		MANUAL
	valve.
		Models Only)			Information section. Be
3. Install one end of gas hose to fitting
					sure to read entire
	on the rear of welder and other end		Headgear		"Welding Guidelines" section before
	of hose to fitting on regulator using				using this equipment.
	hose clamps on each connection. Make	Stud Screw (2)		2. Turn welder off.
	sure gas hose is not kinked or twisted.
				3. Verify surfaces of metals to be joined
4. While standing opposite cylinder
		Tension Nut (2)	Face Shield		are free from dirt, rust, paint, oil,
	outlet, slowly open cylinder valve.
					scale or other contaminants. These
	Inspect for leaks in the connections.
					contaminants make welding difficult
5. Pull trigger on gun to allow gas to		Adjustment
					and cause poor welds.
	flow. Adjust gas regulator to	Arm (2)				All persons
				! WARNING
	maximum flow by moving clockwise.	Lens Retainer
						operating this
	Release trigger.			equipment or in the area while
6. Remember to close gas cylinder valve				equipment is in use must wear
	when finished welding.	Shaded Lens		protective welding gear including: eye
				protection with proper shade, flame
Handshield		Post		resistant clothing, leather welding
		Clear Lens Cover (2)
				gloves and full foot protection.
		Figure 11
Assembly
		1. Remove the lens retainer from the		! WARNING
	Lens	face shield with a regular screwdriver		If heating, welding or
		by prying against the shield and post
				cutting galvanized, zinc
		of the lens retainer.
				plated, lead, or cadmium
	Lens	2. Remove the protective film covering		plated materials, refer to
		from both sides of each lens cover.		the General Safety
	Retainer
		Put one clear lens cover on each side		Information Section for instructions.
				Extremely toxic fumes are created when
		of the shaded lens. Place these three
	Retainer			these metals are heated.
		lenses together into the face shield
				4.	Connect work clamp to work piece or
	Stiffener	and secure with the lens retainer. The
					workbench (if metal). Make sure
		lens retainer should snap into the
					contact is secure. Avoid surfaces with
		second notch in the face shield.
					paint, varnish, corrosion or non-
Figure 9		3. Position one of the holes in the
					metallic materials.
		adjustment arm over the pins which
1.	Cut retainer stiffeners and detachable			5.	Position Heat Selector on front panel
		are located in the ear area of the face
	handle away from shield. Trim the				to desired setting.
		shield. These adjustment arms control
	excess plastic to remove sharp edges.
		the closeness of fit and can be easily
2.	Insert filter lens.				Metal		Heat
		repositioned if necessary.
3. Attach the stiffeners over the pins on		4. Position the headgear inside the face			Thickness		Setting
				24 - 14 Gauge (MIG only)			Low 1 or 2
	the lens retainers (See Figure 9).	shield. Assemble the helmet by
		inserting the stud screw through the		18 - 14 Gauge (Flux Core)
		headgear and shield into the tension		Thicker Than 14 Gauge			High 1 or 2
		nut as shown. Do not tighten tension
		nut completely.		NOTE: These settings are general
		5. Trial fit the welding helmet. Adjust
				guidelines only. Heat setting may vary
		headgear ratchet band to a
				according to welding conditions and
		comfortable position and lower the
Figure 10				materials.
		face shield. If the shield is too far or
www.chpower.com

6