Radio Shack PRO-433 quick start Beyond the Basics Chain search, Banks, the error tone beeps

Page 17

Beyond the Basics

chain search

Chain search lets you search through preset frequency ranges and store found frequencies. You can also modify each range.

	NOTE	At least one bank must be active. If you disable all the
	NOTE	banks, the error tone beeps.
		banks, the error tone beeps.

1. Press SRCH. SRCH appears.

2. (Optional) Press 0 – 9 to enable / disable search banks:

Bank No.	Frequency (MHz)		Step (kHz)
1	29.0000 – 54.0000		5
2	137.0000	– 147.9950	5
3	179.7500	– 215.7500	6000
4	216.0000	– 224.9950	5
5	225.0000	– 399.9875	12.5
6	400.0000	– 449.99375	6.25
7	450.0000	– 469.99375	6.25
8	470.0000	– 512.0000	6.25
9	806.0000	– 956.0000	12.5
10	1240.0000 – 1300.0000		12.5
3. Press or	to search up or down.

4. When the scan pauses, press HOLD/RESUME. To step through the frequencies, press or .

5. To save a frequency, press E/PGM. The bank numbers ﬂash.

6. Enter the target bank number. The smallest empty channel number ﬂashes over the frequency.

7. Press or to select to target channel.

8. Press E/PGM.

To program a search range, complete the following steps:

1. During a chain search, press and hold E/PGM. The lowest and the highest frequencies of Bank 1 appear alternately.

2. Press the number of the bank you want to change. The lower frequency range appears.

17

Image 17

Contents Quick Start PRO-433 1,000 ch Trunking Desktop/Mobile ScannerBasics Contents Quick startBeyond the basics Trunking operationsCare ContentsSpecial features Quick start Installing your scannerBase station Vehicle mountingWall outlet Power your scannerWhen mounting in your dashboard, you will need to If you are not experienced in connecting accessories to Vehicle cigarette lighter or power portVehicle fuse box, use a certiﬁed installer Connect your scannerAntenna Connecting an external speaker mutes the scanner’sExternal speaker Internal speakerTurning on your scanner Quick Start Setting up your scannerStoring frequencies in channels Copying / moving frequenciesSearching for frequencies Quick Start Monitoring and scanning Earphones / headphonesMonitoring ScanningBasics Trunk Basics Your scanner’s controlsPGM Your scanner’s displayScan Replacing the fuse Beyond the basics Appears when you activate the priority featureChannel-storage banks Priority channelsBeyond the Basics Chain search At least one bank must be active. If you disable allBanks, the error tone beeps Weather search and alert Service bank searchIt can take several minutes to search all the service Fips codes Beyond the Basics Skywarn Turn off the data skip feature if it is on Beyond the Basics Signal StalkerData skip Using the memory lock does not prevent the scanner from DelayKeytones Memory lockProgramming trunked frequencies Trunking operationsStoring talk group IDs Talk group IDLocking out a talk group ID Scanning a talk group ID listOne of the ten scan lists must always be active. You Cannot remove all of themLocked out Priority talk group ID scanningMonitoring a talk group ID Talk group ID search range Edacs Trunking Operations AFS FormatStatus Bit S-Bit Ignore You cannot use partial talk groups in decimal modeType I and hybrid trunked systems Trunking Operations Trunk search and scanPreset ﬂeet maps Programming a ﬂeet map Enter size code S-0 Programming base and offset frequenciesFor Motorolla Type II, instead of selecting the size block Motorola disconnect tone detect function Seconds, T-Err appears and wired programming stops Special featuresPC programming Scanner cloningSpecial Features Care TroubleshootingService and repair Resetting the scannerTo ensure that the scanner clears its memory properly Leave it on until CLEAr stops ﬂashingSpeciﬁcations SpeciﬁcationsUBZZ01345ZA0