Radio Shack PRO-433 quick start Programming base and offset frequencies, Enter size code S-0

Page 33

Trunking Operations

codes S-12, S-13, or S-14, these restrictions apply:

•S-12 can only be assigned to Blocks 0, 2, 4, or 6

•S-13 can only be assigned to Blocks 0 and 4

•S-14 can only be assigned to Block 0

Because these size codes require multiple blocks, the NOTE scanner prompts you for the next available block when

you program a ﬂeet map. For example, if you set Block 0 as S-12, b2 is the next block instead of b1. If you assign Block 0 as S-14, you would not see another prompt because S-14 uses all available blocks.

6. Selecte a size code for each desired block.

NOTE	For Motorolla Type II, instead of selecting the size block,
	enter size code S-0.

7. Press SRCH. The scanner searches using the map you programmed.

programming base and offset frequencies

To properly track Motorola VHF and UHF trunked systems, you must program the applicable base and offset frequencies for each system.

1. Select the trunking programming mode.

2. Press the number key of the bank where you want to store the base frequency.

3. Press or to select Motorola Type II UHF or VHF system, then press E/PGM.

4. Press or to select bASE, then press E/PGM.

5. Press the conﬁguration Block Number (1-3) .

6. Press the number keys to enter a new base frequency, then press E/PGM.

7. Press . The display changes to spacing-frequency entry mode.

33

Image 33

Contents Quick Start PRO-433 1,000 ch Trunking Desktop/Mobile ScannerBasics Contents Quick startBeyond the basics Trunking operationsContents Special featuresCare Quick start Installing your scannerBase station Vehicle mountingPower your scanner When mounting in your dashboard, you will need toWall outlet If you are not experienced in connecting accessories to Vehicle cigarette lighter or power portVehicle fuse box, use a certiﬁed installer Connect your scannerAntenna Connecting an external speaker mutes the scanner’sExternal speaker Internal speakerTurning on your scanner Quick Start Setting up your scannerStoring frequencies in channels Copying / moving frequenciesSearching for frequencies Quick Start Monitoring and scanning Earphones / headphonesMonitoring ScanningBasics Trunk Basics Your scanner’s controlsPGM Your scanner’s displayScan Replacing the fuse Beyond the basics Appears when you activate the priority featureChannel-storage banks Priority channelsAt least one bank must be active. If you disable all Banks, the error tone beepsBeyond the Basics Chain search Service bank search It can take several minutes to search all the serviceWeather search and alert Fips codes Beyond the Basics Skywarn Turn off the data skip feature if it is on Beyond the Basics Signal StalkerData skip Using the memory lock does not prevent the scanner from DelayKeytones Memory lockProgramming trunked frequencies Trunking operationsStoring talk group IDs Talk group IDLocking out a talk group ID Scanning a talk group ID listOne of the ten scan lists must always be active. You Cannot remove all of themPriority talk group ID scanning Monitoring a talk group IDLocked out Talk group ID search range Edacs Trunking Operations AFS FormatStatus Bit S-Bit Ignore You cannot use partial talk groups in decimal modeType I and hybrid trunked systems Trunking Operations Trunk search and scanPreset ﬂeet maps Programming a ﬂeet map Programming base and offset frequencies For Motorolla Type II, instead of selecting the size blockEnter size code S-0 Motorola disconnect tone detect function Seconds, T-Err appears and wired programming stops Special featuresPC programming Scanner cloningSpecial Features Care TroubleshootingService and repair Resetting the scannerTo ensure that the scanner clears its memory properly Leave it on until CLEAr stops ﬂashingSpeciﬁcations SpeciﬁcationsUBZZ01345ZA0