Radio Shack PRO-433 quick start Resetting the scanner, Service and repair

Page 38

Care

Why am I missing replies to conversations? Why isn’t my scanner scanning trunked frequencies?

You may have selected an incorrect ﬂeet map. Try another ﬂeet map or program your own.

You may be monitoring a Type I system, but your scanner is set to scan Type II systems. Set you scanner to Type 1 trunked frequencies.

resetting the scanner

Caution: This procedure clears all the information you have stored in the scanner. Before you reset the scanner, try turning it off and on to see if it begins working properly. Reset the scanner only when you are sure it is not working properly.

1. Turn off the scanner.

2. While holding down 2, 9 and HOLD, turn on the scanner. CLEAr ﬂashes for about 5 seconds as the scanner clears its memory.

	NOTE	To ensure that the scanner clears its memory properly,
	NOTE	leave it on until CLEAr stops ﬂashing.
		leave it on until CLEAr stops ﬂashing.

Follow these steps to restore the 150 preprogrammed frequencies stored in the private bank.

1. Turn off the scanner.

2. While holding down 3 and E/PGM, turn on the scanner. After several seconds, the scanner restores the frequencies.

service and repair

If your scanner is not performing correctly, take it to your local RadioShack store for assistance. To locate the nearest RadioShack, use the store locator feature on RadioShack’s website (www. radioshack.com), or call 1-800-The Shack (800-843-7422) and follow the menu options. Modifying or tampering with the scanner’s internal components can cause a malfunction and might invalidate its warranty and void your FCC authorization to operate it.

38

Image 38

Contents PRO-433 1,000 ch Trunking Desktop/Mobile Scanner Quick StartBeyond the basics Contents Quick startBasics Trunking operationsCare ContentsSpecial features Base station Installing your scannerQuick start Vehicle mountingWall outlet Power your scannerWhen mounting in your dashboard, you will need to Vehicle fuse box, use a certiﬁed installer Vehicle cigarette lighter or power portIf you are not experienced in connecting accessories to Connect your scannerExternal speaker Connecting an external speaker mutes the scanner’sAntenna Internal speakerStoring frequencies in channels Quick Start Setting up your scannerTurning on your scanner Copying / moving frequenciesSearching for frequencies Monitoring Earphones / headphonesQuick Start Monitoring and scanning ScanningBasics Basics Your scanner’s controls TrunkYour scanner’s display PGMScan Replacing the fuse Channel-storage banks Appears when you activate the priority featureBeyond the basics Priority channelsBeyond the Basics Chain search At least one bank must be active. If you disable allBanks, the error tone beeps Weather search and alert Service bank searchIt can take several minutes to search all the service Fips codes Beyond the Basics Skywarn Beyond the Basics Signal Stalker Turn off the data skip feature if it is onData skip Keytones DelayUsing the memory lock does not prevent the scanner from Memory lockTrunking operations Programming trunked frequenciesTalk group ID Storing talk group IDsOne of the ten scan lists must always be active. You Scanning a talk group ID listLocking out a talk group ID Cannot remove all of themLocked out Priority talk group ID scanningMonitoring a talk group ID Trunking Operations AFS Format Talk group ID search range EdacsYou cannot use partial talk groups in decimal mode Status Bit S-Bit IgnoreTrunking Operations Trunk search and scan Type I and hybrid trunked systemsPreset ﬂeet maps Programming a ﬂeet map Enter size code S-0 Programming base and offset frequenciesFor Motorolla Type II, instead of selecting the size block Motorola disconnect tone detect function PC programming Special featuresSeconds, T-Err appears and wired programming stops Scanner cloningSpecial Features Troubleshooting CareTo ensure that the scanner clears its memory properly Resetting the scannerService and repair Leave it on until CLEAr stops ﬂashingSpeciﬁcations SpeciﬁcationsUBZZ01345ZA0