Radio Shack PRO-433 quick start Motorola disconnect tone detect function

Page 34

Trunking Operations

8. Enter the frequency using the number keys according to the following guide, then press E/PGM.

•For Motorola Type II VHF (E2-VHF Hi band) use 5kHz steps between 5 kHz – 100 kHz.

•For Motorola Type II UHF (E2-UHF band) use 12.5kHz steps between 12.5 kHz – 100 kHz.

9. Press . The display changes to the offset channel entering mode.

10. Enter an offset channel using the number keys, then press E/PGM. You can only input the frequency between 380 – 759.

11. Press . /CLR /DELAY. The scanner returns to the previous screen. Repeat steps 5-10 if you want to program another conﬁguration.

Motorola disconnect tone detect function

When this function is disabled, the radio looks for squelch before returning to the control channel instead of waiting for the disconnect tone. Only in rare instances will you need to adjust the default settings. The condition to return to control channels depends on whether the signal is present or not.

1. Select the trunking programming mode and the bank you want to change.

2. Press or to select Motorola Type 2 or Motorola Type 1, then press E/PGM.

3.	Press	or	to select Eot, then press E/PGM.
4.	Press	or	to select Eot ON or Eot OFF, then press E/PGM.

If you set the squelch so you hear a hissing sound, the NOTE scanner will remain on the voice channel, even when a

disconnect tone is transmitted or there is no signal at all.

34

Image 34

Contents PRO-433 1,000 ch Trunking Desktop/Mobile Scanner Quick StartBeyond the basics Contents Quick startBasics Trunking operationsSpecial features ContentsCare Base station Installing your scannerQuick start Vehicle mountingWhen mounting in your dashboard, you will need to Power your scannerWall outlet Vehicle fuse box, use a certiﬁed installer Vehicle cigarette lighter or power portIf you are not experienced in connecting accessories to Connect your scannerExternal speaker Connecting an external speaker mutes the scanner’sAntenna Internal speakerStoring frequencies in channels Quick Start Setting up your scannerTurning on your scanner Copying / moving frequenciesSearching for frequencies Monitoring Earphones / headphonesQuick Start Monitoring and scanning ScanningBasics Basics Your scanner’s controls TrunkYour scanner’s display PGMScan Replacing the fuse Channel-storage banks Appears when you activate the priority featureBeyond the basics Priority channelsBanks, the error tone beeps At least one bank must be active. If you disable allBeyond the Basics Chain search It can take several minutes to search all the service Service bank searchWeather search and alert Fips codes Beyond the Basics Skywarn Beyond the Basics Signal Stalker Turn off the data skip feature if it is onData skip Keytones DelayUsing the memory lock does not prevent the scanner from Memory lockTrunking operations Programming trunked frequenciesTalk group ID Storing talk group IDsOne of the ten scan lists must always be active. You Scanning a talk group ID listLocking out a talk group ID Cannot remove all of themMonitoring a talk group ID Priority talk group ID scanningLocked out Trunking Operations AFS Format Talk group ID search range EdacsYou cannot use partial talk groups in decimal mode Status Bit S-Bit IgnoreTrunking Operations Trunk search and scan Type I and hybrid trunked systemsPreset ﬂeet maps Programming a ﬂeet map For Motorolla Type II, instead of selecting the size block Programming base and offset frequenciesEnter size code S-0 Motorola disconnect tone detect function PC programming Special featuresSeconds, T-Err appears and wired programming stops Scanner cloningSpecial Features Troubleshooting CareTo ensure that the scanner clears its memory properly Resetting the scannerService and repair Leave it on until CLEAr stops ﬂashingSpeciﬁcations SpeciﬁcationsUBZZ01345ZA0