Radio Shack PRO-433 quick start Power your scanner, Wall outlet

Page 5

Quick Start

Your scanner requires a 2 x 7-1/8 x 5-5/16 inch (50 x 180 x 135

mm)mounting area. Allow an additional 2-3/8 inch (60 mm) space behind the scanner for connectors and wires.

1. Remove the four rear screws that secure the outer metal case and pull off the case with care.

2. Insert the DIN sleeve into the opening in your dashboard, lip facing out.

3. Push out the top and bottom tabs to hold the sleeve ﬁrmly in place.

4. Slowly slide the scanner into the sleeve until it locks in place.

•When mounting in your dashboard, you will need to

NOTES

connect an external antenna and an external speaker.

•To remove your scanner from the DIN sleeve, insert the two removal keys straight into the scanner’s front panel and pull the scanner out.

step 2: power your scanner

You can power your scanner from a wall outlet, through your vehicle’s ignition, or from your vehicle’s cigarette lighter or power port. You must use a Class 2 power source that supplies 12V DC and delivers at least 500mA. Its center tip must be set to positive and its plug must ﬁt the scanner’s DC 12V jack. Using an adapter that does not meet these speciﬁcations could damage the scanner or the adapter.

	DC 12V
wall outlet	Power source connection.

To prevent electric shock, do not use the AC adapter’s polarized plug with an extension cord, receptacle, or other outlet unless you can fully insert the blades.

1. Connect the tip of the supplied AC adapter to the DC 12V jack.

2. Plug the AC adapter into your wall outlet.

5

Image 5

Contents Quick Start PRO-433 1,000 ch Trunking Desktop/Mobile ScannerBasics Contents Quick startBeyond the basics Trunking operationsCare ContentsSpecial features Quick start Installing your scannerBase station Vehicle mountingWall outlet Power your scannerWhen mounting in your dashboard, you will need to If you are not experienced in connecting accessories to Vehicle cigarette lighter or power portVehicle fuse box, use a certiﬁed installer Connect your scannerAntenna Connecting an external speaker mutes the scanner’sExternal speaker Internal speakerTurning on your scanner Quick Start Setting up your scannerStoring frequencies in channels Copying / moving frequenciesSearching for frequencies Quick Start Monitoring and scanning Earphones / headphonesMonitoring ScanningBasics Trunk Basics Your scanner’s controlsPGM Your scanner’s displayScan Replacing the fuse Beyond the basics Appears when you activate the priority featureChannel-storage banks Priority channelsBeyond the Basics Chain search At least one bank must be active. If you disable allBanks, the error tone beeps Weather search and alert Service bank searchIt can take several minutes to search all the service Fips codes Beyond the Basics Skywarn Turn off the data skip feature if it is on Beyond the Basics Signal StalkerData skip Using the memory lock does not prevent the scanner from DelayKeytones Memory lockProgramming trunked frequencies Trunking operationsStoring talk group IDs Talk group IDLocking out a talk group ID Scanning a talk group ID listOne of the ten scan lists must always be active. You Cannot remove all of themLocked out Priority talk group ID scanningMonitoring a talk group ID Talk group ID search range Edacs Trunking Operations AFS FormatStatus Bit S-Bit Ignore You cannot use partial talk groups in decimal modeType I and hybrid trunked systems Trunking Operations Trunk search and scanPreset ﬂeet maps Programming a ﬂeet map Enter size code S-0 Programming base and offset frequenciesFor Motorolla Type II, instead of selecting the size block Motorola disconnect tone detect function Seconds, T-Err appears and wired programming stops Special featuresPC programming Scanner cloningSpecial Features Care TroubleshootingService and repair Resetting the scannerTo ensure that the scanner clears its memory properly Leave it on until CLEAr stops ﬂashingSpeciﬁcations SpeciﬁcationsUBZZ01345ZA0