Yamaha DPX-1200 manual Checking installation and connections, Pre-operation check, Main unit

Page 16

6Projection

Checking installation and connections

◆Pre-operation check

Prior to projection, adjust settings to suit the location of the main unit and screen, and the input signal you are using.

However, there is usually no need to adjust any settings if you have not changed the installation location or components since the last time you used this unit. Check settings and connections only when the unit does not appear to project images correctly.

Prior to projection, check that the main unit and screen are correctly installed, and that source components are connected correctly.

Main unit

Is the screen installed correctly?	Image source component
“Setting up the projector and screen”

☞page 50

Is the main unit power turned on?

Are the components connected correctly? “Connecting to AV components”

☞ page 48

Is the source component power turned on?

To project images, carry out the following procedure.

Check installation and connections

Select an image for projection and image adjustment

Turn on the projector power.

Begin playback of the source image for adjustment.

Select a projection image.

(Select an input signal and projection image aspect.)

Adjust focus and vertical/ horizontal positioning.

Projection preparations complete

For an explanation of detailed settings, see “Menu”. ☞ page 22 - 40

12

Image 16

Contents DPX-1200 Important Safety Instructions Alleen voor klanten in NederlandWe Want You Listening For a Lifetime FCC Information for US customers onlyIii Table of contents Inappropriate places for installation Accessory checkFeatures Main unit Front panel and controls Main unit Rear panel / Connections Remote control functions Light switch Remote control code switchRemote control cable jack Hide buttonLoading the batteries into the remote control Using the remote control with a wired connectionDistance to sensor Angle to sensor Limits for using the remote controlUse within a left/right arc of 30 degrees If you have not installed the main unit or screen PreparationPrepararion Checking installation and connections Pre-operation checkProjection preparations complete Main unitTurning the projector power on Turning the power onPlacing the DPX-1200 in standby mode Lamp may blink when half lit. This is not a defectMemo Press the STANDBY/ON buttonSelecting using the Input button Selecting an input signalProjection image signal Using the Input button to select a signal Press the + button to open the submenuButton Aspect Input buttonSelecting a display aspect for a projection image Press the Aspect buttonRemote cotrol ButtonDisplay aspect types Input signal typeInput imageDisplay aspectProjected image Representative examplesAdjusting the image Adjusting the vertical position V.POS buttonPattern button Crosshatch pattern Grayscale pattern Color bar patternZoom Menu configurations Menu screenBasic Mode Advanced ModeMenu items Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Hue SaturationColor Temp White CorrectionColor Adjustment Level AdjustmentWhite Peaking IrisSignal Setup Level Hdtv Sync AdjustmentSignal Status TrackingInitial Setup Reset button Remote control only Remote ControlMenu operations Operation button functionsMenu operations 1 with no submenu Press the Menu button to openPress the + or button to select a menu group Menu ButtonPress the + or button to select a suitable setting Setting method depends on the item selectedRemote Control Main Unit Menu Button Remote Control Main UnitMenu operations 2 with submenus Press the h or g button to to adjust item settingsPress the + button to move to Submenu Special menu operations See page 27 for datails about each color itemResetting all parameters Resetting the selected parameterChanging the position of the menu screen Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonAdjusting image quality using the inline menu Example Using the inline menuInline menu composition Inline menu item listMemory configurations Saving memory settingsUsing the remote control Using the menuSettings in the selected memory Press the g button to selectBottom of the screen Press the h or g button to select Memory numberMemory lock Setting Memory LockDeactivating Memory Lock Recall the memory number to be Memory copyCopy source Press the + button to display the confirmation screen Press ButtonResetting to the default settings Initialization of currently selected memoryTo reset all parameters for all memory numbers Press Button to reset Parameters to their default SettingsConnecting to AV components Input Signal type Connector typeSub monitor cable BNC cable for Component connection Pin/BNC Video cable Adapters Pin cableConnecting to computer devices Information for installersInput Signal type For US model onlyMounting the projector on a table Setting up the DPX-1200Mounting the projector on the ceiling When using a 43 screen When using a 169 screenProjection distance Keystone adjustment Using Zoom to adjust image positionUsing V.POS vertical position to adjust image position Using the adjusters to adjust image positionGlossary Test pattern TrackingVista size Pulldown detection style IP conversionCompatible signal types Signal type Active Fsc Color system Lines MHzSignal type Active Pixels Lines KHz Signal type Active Component type Pixels Lines KHzRegular care MaintenanceReplacing the filter Loosen the lamp cover screws Replacing the lampLamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningSpecifications OpticalControls GeneralDimensional drawing 119.1C2004 All Rights Reserved