Yamaha DPX-1200 manual Inappropriate places for installation, Accessory check

Page 6

1Getting started

Inappropriate places for installation

If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the unit itself. Carefully choose the place to install this unit by avoiding the places listed below.

1.Places where the temperature and humidity vary greatly

Do not install this unit in a place where the temperature and humidity become extremely high or the temperature becomes extremely low.

This unit must be used within a temperature range of 5 to 35°C.

2.Places without adequate ventilation

Install this unit with at least 30 cm (1 feet) of ventilation space on the top, right and left, and back.

Do not cover the ventilation slots of this unit. Covering the slots will obstruct heat dissipation.

Install this unit on the firm surface.

Do not cover this unit with a tablecloth, etc.

Make sure there is nothing to get sucked into the ventilation slots so that the temperature of this unit does not become too high.

If you are going to install the unit in a rack, be sure to leave space for ventilation to prevent exhaust overheating the unit.

3.Places where it gets dusty

If the filter is blocked with dust, the temperature of this unit may become too high.

4.Places with too much vibration or impact

Vibration and impact can damage parts of this unit.

5.Places where this unit gets exposed to water or high humidity

If this unit is exposed to water or high humidity, it may cause a fire or electrical shock.

6.Unstable places

If this unit is installed on an unstable or an inclined tabletop, it may fall and cause damage to the unit or personal injury.

7.In close proximity to a Radio or Stereo

The unit may interfere with reception if placed in close proximity to a radio or television receiver.

Warning

To ensure vivid, high contrast images, make sure that no light other than the projector light falls directly on the screen.

Accessory check

Please check that all accessories listed here are included in your package.

 

• Remote control

• Batteries (AA, UM-3 or R6)

• Power cable

Trigger-out DC plug

 

 

 

(For USA only)

AUTO

V. POS

ZOOM

FOCUS

IRIS SETTING PATT

ESCAPEMENU

ASPECT

 

INPUT

RESET

 

HIDE

STILL

 

LIGHT

S VIDEO

A

HDMI

VIDEO

B

D4

 

INPUT

 

 

MEMORY

 

1

2

3

4

5

6

• Pin/BNC adapters

• Lens cap

2

Image 6
Contents DPX-1200 Important Safety Instructions Alleen voor klanten in NederlandWe Want You Listening For a Lifetime FCC Information for US customers onlyIii Table of contents Inappropriate places for installation Accessory checkFeatures Main unit Front panel and controls Main unit Rear panel / Connections Remote control functions Remote control cable jack Light switchRemote control code switch Hide buttonLoading the batteries into the remote control Using the remote control with a wired connectionLimits for using the remote control Distance to sensor Angle to sensorUse within a left/right arc of 30 degrees If you have not installed the main unit or screen PreparationPrepararion Projection preparations complete Checking installation and connectionsPre-operation check Main unitTurning the projector power on Turning the power onMemo Placing the DPX-1200 in standby modeLamp may blink when half lit. This is not a defect Press the STANDBY/ON buttonSelecting an input signal Selecting using the Input buttonProjection image signal Button Aspect Using the Input button to select a signalPress the + button to open the submenu Input buttonRemote cotrol Selecting a display aspect for a projection imagePress the Aspect button ButtonDisplay aspect types Input signal typeInput imageDisplay aspectProjected image Representative examplesPattern button Adjusting the imageAdjusting the vertical position V.POS button Crosshatch pattern Grayscale pattern Color bar patternZoom Menu configurations Menu screenMenu items Basic ModeAdvanced Mode Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Color Temp HueSaturation White CorrectionWhite Peaking Color AdjustmentLevel Adjustment IrisSignal Signal Status Setup Level HdtvSync Adjustment TrackingInitial Setup Menu operations Reset button Remote control onlyRemote Control Operation button functionsPress the + or button to select a menu group Menu operations 1 with no submenuPress the Menu button to open Menu ButtonRemote Control Main Unit Menu Button Press the + or button to select a suitable settingSetting method depends on the item selected Remote Control Main UnitPress the h or g button to to adjust item settings Menu operations 2 with submenusPress the + button to move to Submenu Special menu operations See page 27 for datails about each color itemResetting the selected parameter Resetting all parametersChanging the position of the menu screen Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonInline menu composition Adjusting image quality using the inline menuExample Using the inline menu Inline menu item listUsing the remote control Memory configurationsSaving memory settings Using the menuBottom of the screen Settings in the selected memoryPress the g button to select Press the h or g button to select Memory numberSetting Memory Lock Memory lockDeactivating Memory Lock Memory copy Recall the memory number to beCopy source Press the + button to display the confirmation screen Press ButtonResetting to the default settings Initialization of currently selected memoryTo reset all parameters for all memory numbers Press Button to reset Parameters to their default SettingsSub monitor cable BNC cable for Component connection Connecting to AV componentsInput Signal type Connector type Pin/BNC Video cable Adapters Pin cableInput Signal type Connecting to computer devicesInformation for installers For US model onlySetting up the DPX-1200 Mounting the projector on a tableMounting the projector on the ceiling When using a 169 screen When using a 43 screenProjection distance Using V.POS vertical position to adjust image position Keystone adjustmentUsing Zoom to adjust image position Using the adjusters to adjust image positionGlossary Vista size Test patternTracking Pulldown detection style IP conversionSignal type Active Pixels Lines KHz Compatible signal typesSignal type Active Fsc Color system Lines MHz Signal type Active Component type Pixels Lines KHzMaintenance Regular careReplacing the filter Replacing the lamp Loosen the lamp cover screwsLamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningControls SpecificationsOptical GeneralDimensional drawing 119.1C2004 All Rights Reserved