Yamaha DPX-1200 manual Main unit Front panel and controls

Page 8

3Controls and functions

◆Main unit <Front panel and controls>

Front remote control sensor

STANDBY/ON indicator

	Lamp cover
Exhaust vent	Ventilation inlet

	Lens	1
	Lens	2
		2
		3
	Lens cap	4
	Adjustable feet	5

Makes small adjustments to the projection angle

1

STANDBY/ON

ESCAPE

MENU

PATTERN SETTING

ASPECT	INPUT
LAMP COVER TEMP	FAN

DIGITAL CINEMA PROJECTOR DPX-1200

6

7

8

9

0

1LED Indicators

The main unit is equipped with 5 indicators to display various states of operation. See page 61 for explanations of the LED indicator

meanings.

STANDBY/ON

A

ESCAPE

MENU

PATTERN SETTING

ASPECT			INPUT
B	LAMP COVER TEMP	FAN	E
B			E
C			D

ASTANDBY/ON indicator

(There is also an LED on the front panel of the main unit.)

BLAMP warning indicator

CCOVER warning indicator

DTEMP warning indicator

EFAN warning indicator

2STANDBY/ON button

Switches the unit between Standby and On (operational) modes.

3ESCAPE button

Exits from submenus.

4PATTERN button

Switches the built-in test pattern on and off.

5ASPECT button

Turns the display aspect menu for the project image on and off.

7MENU button

Switches the settings and adjustments menu display on and off.

8SETTING button

Selects lens adjustment modes.

9INPUT button

Switches the input signal selection menu display on and off.

0Cursor buttons

Use the h, g, +, - buttons for system operations, menu item selection, and changing system values.

6 (Enter) button

Sets values when the DPX-1200 is displaying the menu. When the menu is not displayed, the DPX-1200 displays the in-line image quality adjustment menu. (☞ page 40)

4

Image 8

Contents DPX-1200 Important Safety Instructions Alleen voor klanten in NederlandWe Want You Listening For a Lifetime FCC Information for US customers onlyIii Table of contents Inappropriate places for installation Accessory checkFeatures Main unit Front panel and controls Main unit Rear panel / Connections Remote control functions Light switch Remote control code switchRemote control cable jack Hide buttonLoading the batteries into the remote control Using the remote control with a wired connectionUse within a left/right arc of 30 degrees Limits for using the remote controlDistance to sensor Angle to sensor If you have not installed the main unit or screen PreparationPrepararion Checking installation and connections Pre-operation checkProjection preparations complete Main unitTurning the projector power on Turning the power onPlacing the DPX-1200 in standby mode Lamp may blink when half lit. This is not a defectMemo Press the STANDBY/ON buttonProjection image signal Selecting an input signalSelecting using the Input button Using the Input button to select a signal Press the + button to open the submenuButton Aspect Input buttonSelecting a display aspect for a projection image Press the Aspect buttonRemote cotrol ButtonDisplay aspect types Input signal typeInput imageDisplay aspectProjected image Representative examplesAdjusting the image Adjusting the vertical position V.POS buttonPattern button Crosshatch pattern Grayscale pattern Color bar patternZoom Menu configurations Menu screenBasic Mode Advanced ModeMenu items Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Hue SaturationColor Temp White CorrectionColor Adjustment Level AdjustmentWhite Peaking IrisSignal Setup Level Hdtv Sync AdjustmentSignal Status TrackingInitial Setup Reset button Remote control only Remote ControlMenu operations Operation button functionsMenu operations 1 with no submenu Press the Menu button to openPress the + or button to select a menu group Menu ButtonPress the + or button to select a suitable setting Setting method depends on the item selectedRemote Control Main Unit Menu Button Remote Control Main UnitPress the + button to move to Submenu Press the h or g button to to adjust item settingsMenu operations 2 with submenus Special menu operations See page 27 for datails about each color itemChanging the position of the menu screen Resetting the selected parameterResetting all parameters Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonAdjusting image quality using the inline menu Example Using the inline menuInline menu composition Inline menu item listMemory configurations Saving memory settingsUsing the remote control Using the menuSettings in the selected memory Press the g button to selectBottom of the screen Press the h or g button to select Memory numberDeactivating Memory Lock Setting Memory LockMemory lock Copy source Memory copyRecall the memory number to be Press the + button to display the confirmation screen Press ButtonResetting to the default settings Initialization of currently selected memoryTo reset all parameters for all memory numbers Press Button to reset Parameters to their default SettingsConnecting to AV components Input Signal type Connector typeSub monitor cable BNC cable for Component connection Pin/BNC Video cable Adapters Pin cableConnecting to computer devices Information for installersInput Signal type For US model onlyMounting the projector on the ceiling Setting up the DPX-1200Mounting the projector on a table Projection distance When using a 169 screenWhen using a 43 screen Keystone adjustment Using Zoom to adjust image positionUsing V.POS vertical position to adjust image position Using the adjusters to adjust image positionGlossary Test pattern TrackingVista size Pulldown detection style IP conversionCompatible signal types Signal type Active Fsc Color system Lines MHzSignal type Active Pixels Lines KHz Signal type Active Component type Pixels Lines KHzReplacing the filter MaintenanceRegular care Lamp cover screws Replacing the lampLoosen the lamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningSpecifications OpticalControls GeneralDimensional drawing 119.1C2004 All Rights Reserved