Yamaha DPX-1200 manual We Want You Listening For a Lifetime, FCC Information for US customers only

Page 3

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation

Address: 6660 Orangethorpe Avenue

Buena Park, CA90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: Projector

Model Name: DPX-1200

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1)this device may not cause harmful interference, and

2)this device must accept any interference received including interference that may cause undesired operation. See the user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

Compliance with FCC regulations does not guarantee that

UNIT!

interference will not occur in all installations. If this product is

This product, when installed as indicated in the instructions

found to be the source of interference, which can be determined

by turning the unit “OFF” and “ON”, please try to eliminate the

contained in this manual, meets FCC requirements.

problem by using one of the following measures:

Modifications not expressly approved by Yamaha may void

 

your authority, granted by the FCC, to use the product.

Relocate either this product or the device that is being affected

2. IMPORTANT: When connecting this product to accessories

by the interference.

 

and/or another product use only high quality shielded

Utilize power outlets that are on different branch (circuit

cables. Cable/s supplied with this product MUST be used.

breaker or fuse) circuits or install AC line filter/s.

Follow all installation instructions. Failure to follow

In the case of radio or TV interference, relocate/reorient the

instructions could void your FCC authorization to use this

antenna. If the antenna lead-in is 300 ohm ribbon lead, change

product in the USA.

the lead-in to coaxial type cable.

3. NOTE: This product has been tested and found to comply

If these corrective measures do not produce satisfactory results,

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these

please contact the local retailer authorized to distribute this type

requirements provides a reasonable level of assurance that

of product. If you can not locate the appropriate retailer, please

your use of this product in a residential environment will not

contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe

result in harmful interference with other electronic devices.

Ave, Buena Park, CA 90620.

This equipment generates/uses radio frequencies and, if not

The above statements apply ONLY to those products distributed

installed and used according to the instructions found in the

by Yamaha Corporation of America or its subsidiaries.

users manual, may cause interference harmful to the operation

 

of other electronic devices.

 

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

ii

Page 2 Page 4
Image 3
Page 2 Page 4
Contents DPX-1200 Alleen voor klanten in Nederland Important Safety InstructionsFCC Information for US customers only We Want You Listening For a LifetimeIii Table of contents Accessory check Inappropriate places for installationFeatures Main unit Front panel and controls Main unit Rear panel / Connections Remote control functions Hide button Light switchRemote control code switch Remote control cable jackUsing the remote control with a wired connection Loading the batteries into the remote controlLimits for using the remote control Distance to sensor Angle to sensorUse within a left/right arc of 30 degrees Preparation If you have not installed the main unit or screenPrepararion Main unit Checking installation and connectionsPre-operation check Projection preparations completeTurning the power on Turning the projector power onPress the STANDBY/ON button Placing the DPX-1200 in standby modeLamp may blink when half lit. This is not a defect MemoSelecting an input signal Selecting using the Input buttonProjection image signal Input button Using the Input button to select a signalPress the + button to open the submenu Button AspectButton Selecting a display aspect for a projection imagePress the Aspect button Remote cotrolDisplay aspect types Representative examples Input signal typeInput imageDisplay aspectProjected imageCrosshatch pattern Grayscale pattern Color bar pattern Adjusting the imageAdjusting the vertical position V.POS button Pattern buttonZoom Menu screen Menu configurationsMenu item list Basic ModeAdvanced Mode Menu itemsLower level menu items Submenu ItemsMenu group items and functions White Correction HueSaturation Color TempIris Color AdjustmentLevel Adjustment White PeakingSignal Tracking Setup Level HdtvSync Adjustment Signal StatusInitial Setup Operation button functions Reset button Remote control onlyRemote Control Menu operationsMenu Button Menu operations 1 with no submenuPress the Menu button to open Press the + or button to select a menu groupRemote Control Main Unit Press the + or button to select a suitable settingSetting method depends on the item selected Remote Control Main Unit Menu ButtonPress the h or g button to to adjust item settings Menu operations 2 with submenusPress the + button to move to Submenu See page 27 for datails about each color item Special menu operationsResetting the selected parameter Resetting all parametersChanging the position of the menu screen Subtitle Zoom Resetting the lamp running timePress the button Changing the GammaInline menu item list Adjusting image quality using the inline menuExample Using the inline menu Inline menu compositionUsing the menu Memory configurationsSaving memory settings Using the remote controlPress the h or g button to select Memory number Settings in the selected memoryPress the g button to select Bottom of the screenSetting Memory Lock Memory lockDeactivating Memory Lock Memory copy Recall the memory number to beCopy source Press Button Press the + button to display the confirmation screenInitialization of currently selected memory Resetting to the default settingsPress Button to reset Parameters to their default Settings To reset all parameters for all memory numbersPin/BNC Video cable Adapters Pin cable Connecting to AV componentsInput Signal type Connector type Sub monitor cable BNC cable for Component connectionFor US model only Connecting to computer devicesInformation for installers Input Signal typeSetting up the DPX-1200 Mounting the projector on a tableMounting the projector on the ceiling When using a 169 screen When using a 43 screenProjection distance Using the adjusters to adjust image position Keystone adjustmentUsing Zoom to adjust image position Using V.POS vertical position to adjust image positionGlossary Pulldown detection style IP conversion Test patternTracking Vista sizeSignal type Active Component type Pixels Lines KHz Compatible signal typesSignal type Active Fsc Color system Lines MHz Signal type Active Pixels Lines KHzMaintenance Regular careReplacing the filter Replacing the lamp Loosen the lamp cover screwsLamp cover screws To protect the lamp, you cannot turn on TroubleshootingTroubleshooting Message Condition Message displayLED indicator State Meaning LED indicator meaningsGeneral SpecificationsOptical Controls119.1 Dimensional drawingC2004 All Rights Reserved
Top Page Image Contents