Yamaha manual Placing the DPX-1200 in standby mode, Memo, Press the STANDBY/ON button

Page 18

Turning the projector power on

Placing the DPX-1200 in standby mode

 

button

STANDBY/ON button

AUTO

 

 

 

 

 

 

 

STANDBY/ON

 

V. POS

ZOOM

FOCUS

 

 

IRIS

SETTING

PATT

 

 

 

 

 

ESCAPE

MENU

ESCAPE

 

MENU

 

 

 

 

 

PATTERN

SETTING

 

 

 

ASPECT

INPUT

ASPECT

 

INPUT

LAMP COVER TEMP

FAN

 

 

 

Remote Control

Main unit

1. Press the STANDBY/ON button.

A confirmation message appears on the screen.

Press again to enter standby.

AC inlet

2.If you wish to place the DPX-1200 in standby mode, press the STANDBY/ON button again.

The lamp changes to a half lit state, and the fan activates for 2 minutes to cool the lamp. During this time, the STANDBY/ON indicator blinks orange, and pressing STANDBY/ON does not turn main unit power on again. When the unit finishes cooling, the fan stops, and the STANDBY/ ON indicator turns orange.

Memo

The lamp may blink when half lit. This is not a defect.

Warning

• Do not remove the power cable while the STANDBY/ON indicator is blinking green or when the fan is activated. This could damage the lamp or reduce lamp life.

• If you do not plan to use the main unit for a long period of time, attach the lens cap and remove the plug from the AC outlet.

• Condensation may appear on the unit if the temperature of the surrounding environment changes quickly. Condensation may also cause the projected image to be cloudy. Place the unit in standby mode until the condensation disappears. Switching the unit on when condensation is present may damage the unit.

14

Image 18
Contents DPX-1200 Important Safety Instructions Alleen voor klanten in NederlandWe Want You Listening For a Lifetime FCC Information for US customers onlyIii Table of contents Inappropriate places for installation Accessory checkFeatures Main unit Front panel and controls Main unit Rear panel / Connections Remote control functions Remote control cable jack Light switchRemote control code switch Hide buttonLoading the batteries into the remote control Using the remote control with a wired connectionLimits for using the remote control Distance to sensor Angle to sensorUse within a left/right arc of 30 degrees If you have not installed the main unit or screen PreparationPrepararion Projection preparations complete Checking installation and connectionsPre-operation check Main unitTurning the projector power on Turning the power onMemo Placing the DPX-1200 in standby modeLamp may blink when half lit. This is not a defect Press the STANDBY/ON buttonSelecting an input signal Selecting using the Input buttonProjection image signal Button Aspect Using the Input button to select a signalPress the + button to open the submenu Input buttonRemote cotrol Selecting a display aspect for a projection imagePress the Aspect button ButtonDisplay aspect types Input signal typeInput imageDisplay aspectProjected image Representative examplesPattern button Adjusting the imageAdjusting the vertical position V.POS button Crosshatch pattern Grayscale pattern Color bar patternZoom Menu configurations Menu screenMenu items Basic ModeAdvanced Mode Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Color Temp HueSaturation White CorrectionWhite Peaking Color AdjustmentLevel Adjustment IrisSignal Signal Status Setup Level HdtvSync Adjustment TrackingInitial Setup Menu operations Reset button Remote control onlyRemote Control Operation button functionsPress the + or button to select a menu group Menu operations 1 with no submenuPress the Menu button to open Menu ButtonRemote Control Main Unit Menu Button Press the + or button to select a suitable settingSetting method depends on the item selected Remote Control Main UnitPress the h or g button to to adjust item settings Menu operations 2 with submenusPress the + button to move to Submenu Special menu operations See page 27 for datails about each color itemResetting the selected parameter Resetting all parametersChanging the position of the menu screen Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonInline menu composition Adjusting image quality using the inline menuExample Using the inline menu Inline menu item listUsing the remote control Memory configurationsSaving memory settings Using the menuBottom of the screen Settings in the selected memoryPress the g button to select Press the h or g button to select Memory numberSetting Memory Lock Memory lockDeactivating Memory Lock Memory copy Recall the memory number to beCopy source Press the + button to display the confirmation screen Press ButtonResetting to the default settings Initialization of currently selected memoryTo reset all parameters for all memory numbers Press Button to reset Parameters to their default SettingsSub monitor cable BNC cable for Component connection Connecting to AV componentsInput Signal type Connector type Pin/BNC Video cable Adapters Pin cableInput Signal type Connecting to computer devicesInformation for installers For US model onlySetting up the DPX-1200 Mounting the projector on a tableMounting the projector on the ceiling When using a 169 screen When using a 43 screenProjection distance Using V.POS vertical position to adjust image position Keystone adjustmentUsing Zoom to adjust image position Using the adjusters to adjust image positionGlossary Vista size Test patternTracking Pulldown detection style IP conversionSignal type Active Pixels Lines KHz Compatible signal typesSignal type Active Fsc Color system Lines MHz Signal type Active Component type Pixels Lines KHzMaintenance Regular careReplacing the filter Replacing the lamp Loosen the lamp cover screwsLamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningControls SpecificationsOptical GeneralDimensional drawing 119.1C2004 All Rights Reserved