Hue, Saturation, Color Temp, White Correction

Yamaha DPX-1200 Hue, Saturation, Color Temp, White Correction, Sharpness Type, Sharpness Gain

Page 30

Menu items

Hue	Sets the hue or phase of the image.
(Input signal)	•	+ side (0 to +50)	: Shifts the hue towards blue coloration.
	•	- side (-50 to 0)	: Shifts the hue towards red coloration.
Video/S-Video/Component/RGB TV

Saturation	Adjusts the degree to which color depth is expressed in the image.
(Input signal)	•	+ side (+100 to + 200)	: The unit projects colors with greater depth.
	•	- side (0 to +100)	: The unit projects colors with less depth.
Video/S-Video/Component/RGB TV

	Color Temp.	Adjusts color temperature.
	(Input signal)	Adjusts the level of white in colors between red and blue, and between green and magenta.
	(Input signal)	Increase the color temperature to increase the amount of blue in an image, giving bright
	Video/S-Video/Component/RGB TV/RGB PC
		color tones. Reduce the color temperature to increase the amount of red, giving a darker,
	Adjust in the [Color Adjustment] menu in	more relaxed atmosphere to the image.
	advanced mode.	Choices: 5,000 to 10,000

Color temprature

adjustment

	White Correction	Adjusts hUV.
	(Input signal)	Increasing the hUV setting increases the amount of green in the image. Decreasing this
	(Input signal)	setting increases the amount of magenta.
	Video/S-Video/Component/RGB TV/RGB PC	setting increases the amount of magenta.
		Choices: -0.02 to +0.02

Adjust in the [Color Adjustment] menu in advanced mode.

hUV

–

	Sharpness Type	Changes the characteristics of the filter used for “Sharpness Gain”
	(Input signal)	(described below).
	Video/S-Video/Component/RGB TV	Choices: Off / L / ML / MH / H

	Sharpness Gain	Adjusts the clearness of the image edges.
	(Input signal)	Increase this figure to render a sharper image, or reduce it to give a softer image with less
	(Input signal)	image noise. You cannot adjust this parameter if [Sharpness Type] is set to [Off].
	Video/S-Video/Component/RGB TV
		Choices: 0 to 10

Image 30

Contents

DPX-1200 Important Safety Instructions Alleen voor klanten in NederlandWe Want You Listening For a Lifetime FCC Information for US customers onlyIii Table of contents Inappropriate places for installation Accessory checkFeatures Main unit Front panel and controls Main unit Rear panel / Connections Remote control functions Remote control cable jack Light switchRemote control code switch Hide buttonLoading the batteries into the remote control Using the remote control with a wired connectionLimits for using the remote control Distance to sensor Angle to sensorUse within a left/right arc of 30 degrees If you have not installed the main unit or screen PreparationPrepararion Projection preparations complete Checking installation and connectionsPre-operation check Main unitTurning the projector power on Turning the power onMemo Placing the DPX-1200 in standby modeLamp may blink when half lit. This is not a defect Press the STANDBY/ON buttonSelecting an input signal Selecting using the Input buttonProjection image signal Button Aspect Using the Input button to select a signalPress the + button to open the submenu Input buttonRemote cotrol Selecting a display aspect for a projection imagePress the Aspect button ButtonDisplay aspect types Input signal typeInput imageDisplay aspectProjected image Representative examplesPattern button Adjusting the imageAdjusting the vertical position V.POS button Crosshatch pattern Grayscale pattern Color bar patternZoom Menu configurations Menu screen Menu items Basic Mode Advanced Mode Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Color Temp HueSaturation White CorrectionWhite Peaking Color AdjustmentLevel Adjustment IrisSignal Signal Status Setup Level HdtvSync Adjustment TrackingInitial Setup Menu operations Reset button Remote control onlyRemote Control Operation button functionsPress the + or button to select a menu group Menu operations 1 with no submenuPress the Menu button to open Menu ButtonRemote Control Main Unit Menu Button Press the + or button to select a suitable settingSetting method depends on the item selected Remote Control Main UnitPress the h or g button to to adjust item settings Menu operations 2 with submenusPress the + button to move to Submenu Special menu operations See page 27 for datails about each color itemResetting the selected parameter Resetting all parametersChanging the position of the menu screen Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonInline menu composition Adjusting image quality using the inline menuExample Using the inline menu Inline menu item listUsing the remote control Memory configurationsSaving memory settings Using the menuBottom of the screen Settings in the selected memoryPress the g button to select Press the h or g button to select Memory numberSetting Memory Lock Memory lockDeactivating Memory Lock Memory copy Recall the memory number to beCopy source Press the + button to display the confirmation screen Press ButtonResetting to the default settings Initialization of currently selected memoryTo reset all parameters for all memory numbers Press Button to reset Parameters to their default SettingsSub monitor cable BNC cable for Component connection Connecting to AV componentsInput Signal type Connector type Pin/BNC Video cable Adapters Pin cableInput Signal type Connecting to computer devicesInformation for installers For US model onlySetting up the DPX-1200 Mounting the projector on a tableMounting the projector on the ceiling When using a 169 screen When using a 43 screenProjection distance Using V.POS vertical position to adjust image position Keystone adjustmentUsing Zoom to adjust image position Using the adjusters to adjust image positionGlossary Vista size Test patternTracking Pulldown detection style IP conversionSignal type Active Pixels Lines KHz Compatible signal typesSignal type Active Fsc Color system Lines MHz Signal type Active Component type Pixels Lines KHzMaintenance Regular careReplacing the filter Replacing the lamp Loosen the lamp cover screwsLamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningControls SpecificationsOptical GeneralDimensional drawing 119.1C2004 All Rights Reserved

Yamaha DPX-1200 Hue, Saturation, Color Temp, White Correction, Sharpness Type, Sharpness Gain

Hue

Sets the hue or phase of the image.

Saturation

Color Temp.

Adjusts color temperature.

White Correction

Adjusts hUV.

Sharpness Type

Sharpness Gain

Adjusts the clearness of the image edges.