Yamaha DPX-1200 manual Maintenance, Regular care, Replacing the filter

Page 60

Maintenance

Regular care

Be sure to disconnect the power cable before doing any maintenance.

<Main unit>

Wipe with a soft cloth. Use a damp cloth with a mild detergent and then wipe with a dry cloth again if the unit is heavily soiled. Do not use strong solvents such as thinner or alcohol as they may damage the unit casing.

<Lens>

Use commercially available blowers or lens tissue to remove any dirt from the lens.

<Filter>

If dust accumulates on the ventilation port filter, the internal temperature of the unit rises, which may cause damage to the unit. Clean the filter approximately once every 200 hours. Remove the power cable from the AC outlet, and remove dust from the filter with a vacuum cleaner.

To prevent dust from entering the filter itself, be sure to vacuum the filter with the unit on its side.

Replacing the filter

Replace the filter when it becomes difficult to remove dust from it.

1. Turn off the power and remove the power cable.

2. Carefully place the unit upside down on a soft cloth to prevent scratching.

3. Press the filter hook on the underside of the main unit to remove the filter.

4. Firmly attach the new filter. The lamp does not light if the filter is incorrectly attached.

Warning

• Contact a YAMAHA dealer or service center if you require replacement filters.

56

Image 60
Contents DPX-1200 Important Safety Instructions Alleen voor klanten in NederlandWe Want You Listening For a Lifetime FCC Information for US customers onlyIii Table of contents Inappropriate places for installation Accessory checkFeatures Main unit Front panel and controls Main unit Rear panel / Connections Remote control functions Light switch Remote control code switchRemote control cable jack Hide buttonLoading the batteries into the remote control Using the remote control with a wired connectionLimits for using the remote control Distance to sensor Angle to sensorUse within a left/right arc of 30 degrees If you have not installed the main unit or screen PreparationPrepararion Checking installation and connections Pre-operation checkProjection preparations complete Main unitTurning the projector power on Turning the power onPlacing the DPX-1200 in standby mode Lamp may blink when half lit. This is not a defectMemo Press the STANDBY/ON buttonSelecting an input signal Selecting using the Input buttonProjection image signal Using the Input button to select a signal Press the + button to open the submenuButton Aspect Input buttonSelecting a display aspect for a projection image Press the Aspect buttonRemote cotrol ButtonDisplay aspect types Input signal typeInput imageDisplay aspectProjected image Representative examplesAdjusting the image Adjusting the vertical position V.POS buttonPattern button Crosshatch pattern Grayscale pattern Color bar patternZoom Menu configurations Menu screenBasic Mode Advanced ModeMenu items Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Hue SaturationColor Temp White CorrectionColor Adjustment Level AdjustmentWhite Peaking IrisSignal Setup Level Hdtv Sync AdjustmentSignal Status TrackingInitial Setup Reset button Remote control only Remote ControlMenu operations Operation button functionsMenu operations 1 with no submenu Press the Menu button to openPress the + or button to select a menu group Menu ButtonPress the + or button to select a suitable setting Setting method depends on the item selectedRemote Control Main Unit Menu Button Remote Control Main UnitPress the h or g button to to adjust item settings Menu operations 2 with submenusPress the + button to move to Submenu Special menu operations See page 27 for datails about each color itemResetting the selected parameter Resetting all parametersChanging the position of the menu screen Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonAdjusting image quality using the inline menu Example Using the inline menuInline menu composition Inline menu item listMemory configurations Saving memory settingsUsing the remote control Using the menuSettings in the selected memory Press the g button to selectBottom of the screen Press the h or g button to select Memory numberSetting Memory Lock Memory lockDeactivating Memory Lock Memory copy Recall the memory number to beCopy source Press the + button to display the confirmation screen Press ButtonResetting to the default settings Initialization of currently selected memoryTo reset all parameters for all memory numbers Press Button to reset Parameters to their default SettingsConnecting to AV components Input Signal type Connector typeSub monitor cable BNC cable for Component connection Pin/BNC Video cable Adapters Pin cableConnecting to computer devices Information for installersInput Signal type For US model onlySetting up the DPX-1200 Mounting the projector on a tableMounting the projector on the ceiling When using a 169 screen When using a 43 screenProjection distance Keystone adjustment Using Zoom to adjust image positionUsing V.POS vertical position to adjust image position Using the adjusters to adjust image positionGlossary Test pattern TrackingVista size Pulldown detection style IP conversionCompatible signal types Signal type Active Fsc Color system Lines MHzSignal type Active Pixels Lines KHz Signal type Active Component type Pixels Lines KHzMaintenance Regular careReplacing the filter Replacing the lamp Loosen the lamp cover screwsLamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningSpecifications OpticalControls GeneralDimensional drawing 119.1C2004 All Rights Reserved