Yamaha DPX-1200 manual Turning the projector power on, Turning the power on

Page 17

Turning the projector power on

◆Turning the power on

Always remove the lens cap before operating the main unit.

STANDBY/ON

STANDBY/ON

1. Insert the supplied power cable

 

firmly into the AC inlet at the rear

 

indicator

ESCAPE

MENU

of the main unit, then insert the

PATTERN

SETTING

plug into an AC outlet.

LAMP COVER TEMP FAN

INPUT

The STANDBY/ON indicator lights orange.

ASPECT

 

 

 

AC inlet

 

 

button STANDBY/ON button

AUTO

 

 

 

 

 

 

STANDBY/ON

V. POS

ZOOM

FOCUS

 

IRIS

SETTING

PATT

 

 

 

ESCAPE

MENU

ESCAPE

 

MENU

 

 

 

PATTERN

SETTING

 

 

ASPECT

INPUT

ASPECT

 

INPUT

LAMP COVER TEMP FAN

 

 

Remote Control

Main unit

2.Press the STANDBY/ON button

(the button on the remote control).

The indicator blinks green and the lamp lights up in preparation for projection. After approximately 35 seconds, the indicator changes from blinking to solid green, indicating that the unit is ready to project.

Warning

•Do not remove the power cable while the STANDBY/ON indicator is blinking green or lit steady green. This could damage the lamp or reduce lamp life.

6

Projection

13

Page 16 Page 18
Image 17
Page 16 Page 18
Contents
DPX-1200 Alleen voor klanten in Nederland Important Safety InstructionsFCC Information for US customers only We Want You Listening For a LifetimeIii Table of contents Accessory check Inappropriate places for installationFeatures Main unit Front panel and controls Main unit Rear panel / Connections Remote control functions Remote control code switch Light switchRemote control cable jack Hide buttonUsing the remote control with a wired connection Loading the batteries into the remote controlUse within a left/right arc of 30 degrees Limits for using the remote controlDistance to sensor Angle to sensor Preparation If you have not installed the main unit or screenPrepararion Pre-operation check Checking installation and connectionsProjection preparations complete Main unitTurning the power on Turning the projector power onLamp may blink when half lit. This is not a defect Placing the DPX-1200 in standby modeMemo Press the STANDBY/ON buttonProjection image signal Selecting an input signalSelecting using the Input button Press the + button to open the submenu Using the Input button to select a signalButton Aspect Input buttonPress the Aspect button Selecting a display aspect for a projection imageRemote cotrol ButtonDisplay aspect types Representative examples Input signal typeInput imageDisplay aspectProjected imageAdjusting the vertical position V.POS button Adjusting the imagePattern button Crosshatch pattern Grayscale pattern Color bar patternZoom Menu screen Menu configurationsAdvanced Mode Basic ModeMenu items Menu item listLower level menu items Submenu ItemsMenu group items and functions Saturation HueColor Temp White CorrectionLevel Adjustment Color AdjustmentWhite Peaking IrisSignal Sync Adjustment Setup Level HdtvSignal Status TrackingInitial Setup Remote Control Reset button Remote control onlyMenu operations Operation button functionsPress the Menu button to open Menu operations 1 with no submenuPress the + or button to select a menu group Menu ButtonSetting method depends on the item selected Press the + or button to select a suitable settingRemote Control Main Unit Menu Button Remote Control Main UnitPress the + button to move to Submenu Press the h or g button to to adjust item settingsMenu operations 2 with submenus See page 27 for datails about each color item Special menu operationsChanging the position of the menu screen Resetting the selected parameterResetting all parameters Subtitle Zoom Resetting the lamp running timePress the button Changing the GammaExample Using the inline menu Adjusting image quality using the inline menuInline menu composition Inline menu item listSaving memory settings Memory configurationsUsing the remote control Using the menuPress the g button to select Settings in the selected memoryBottom of the screen Press the h or g button to select Memory numberDeactivating Memory Lock Setting Memory LockMemory lock Copy source Memory copyRecall the memory number to be Press Button Press the + button to display the confirmation screenInitialization of currently selected memory Resetting to the default settingsPress Button to reset Parameters to their default Settings To reset all parameters for all memory numbersInput Signal type Connector type Connecting to AV componentsSub monitor cable BNC cable for Component connection Pin/BNC Video cable Adapters Pin cableInformation for installers Connecting to computer devicesInput Signal type For US model onlyMounting the projector on the ceiling Setting up the DPX-1200Mounting the projector on a table Projection distance When using a 169 screenWhen using a 43 screen Using Zoom to adjust image position Keystone adjustmentUsing V.POS vertical position to adjust image position Using the adjusters to adjust image positionGlossary Tracking Test patternVista size Pulldown detection style IP conversionSignal type Active Fsc Color system Lines MHz Compatible signal typesSignal type Active Pixels Lines KHz Signal type Active Component type Pixels Lines KHzReplacing the filter MaintenanceRegular care Lamp cover screws Replacing the lampLoosen the lamp cover screws To protect the lamp, you cannot turn on TroubleshootingTroubleshooting Message Condition Message displayLED indicator State Meaning LED indicator meaningsOptical SpecificationsControls General119.1 Dimensional drawingC2004 All Rights Reserved
Top Page Image Contents