Yamaha DPX-1200 manual Test pattern, Tracking, Vista size, Pulldown detection style IP conversion

Page 58

Glossary

Test pattern

This unit contains test patterns which you can use to adjust the position and focus of the projected image on the screen.

Tracking

Computers output signals with a given regular frequency, which you must synchronize the projector to in order to produce a good quality image. If you do not match the phase of the signal, vertical stripes may appear on the image.

Vista size

A standard film size, with an aspect ratio of 1.85:1 in North America, and 1.66:1 in Europe.

3-2 pulldown detection style IP conversion

A function for directly converting interlace signal into sixty frame progressive signal used when receiving 60 field interlace signal from an image source recorded with the same 24 frames as movie film. This allows DVD and other materiel recorded with 24 frames to be projected on large screens as a natural, precise image with no loss of quality, comparable to a movie film.

*DLPTM, DMDTM, DarkChip2TM, and DarkChip3TM are registered trademarks of the Texas Instruments corporation of America.

*“DCDi” is a trademark of Faroudja, a division of Genesis Microchip, Inc.

*HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademark of HDMI Licensing LLC.

54

Image 58

Contents DPX-1200 Important Safety Instructions Alleen voor klanten in NederlandWe Want You Listening For a Lifetime FCC Information for US customers onlyIii Table of contents Inappropriate places for installation Accessory checkFeatures Main unit Front panel and controls Main unit Rear panel / Connections Remote control functions Remote control cable jack Light switchRemote control code switch Hide buttonLoading the batteries into the remote control Using the remote control with a wired connectionDistance to sensor Angle to sensor Limits for using the remote controlUse within a left/right arc of 30 degrees If you have not installed the main unit or screen PreparationPrepararion Projection preparations complete Checking installation and connectionsPre-operation check Main unitTurning the projector power on Turning the power onMemo Placing the DPX-1200 in standby modeLamp may blink when half lit. This is not a defect Press the STANDBY/ON buttonSelecting using the Input button Selecting an input signalProjection image signal Button Aspect Using the Input button to select a signalPress the + button to open the submenu Input buttonRemote cotrol Selecting a display aspect for a projection imagePress the Aspect button ButtonDisplay aspect types Input signal typeInput imageDisplay aspectProjected image Representative examplesPattern button Adjusting the imageAdjusting the vertical position V.POS button Crosshatch pattern Grayscale pattern Color bar patternZoom Menu configurations Menu screenMenu items Basic ModeAdvanced Mode Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Color Temp HueSaturation White CorrectionWhite Peaking Color AdjustmentLevel Adjustment IrisSignal Signal Status Setup Level HdtvSync Adjustment TrackingInitial Setup Menu operations Reset button Remote control onlyRemote Control Operation button functionsPress the + or button to select a menu group Menu operations 1 with no submenuPress the Menu button to open Menu ButtonRemote Control Main Unit Menu Button Press the + or button to select a suitable settingSetting method depends on the item selected Remote Control Main UnitMenu operations 2 with submenus Press the h or g button to to adjust item settingsPress the + button to move to Submenu Special menu operations See page 27 for datails about each color itemResetting all parameters Resetting the selected parameterChanging the position of the menu screen Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonInline menu composition Adjusting image quality using the inline menuExample Using the inline menu Inline menu item listUsing the remote control Memory configurationsSaving memory settings Using the menuBottom of the screen Settings in the selected memoryPress the g button to select Press the h or g button to select Memory numberMemory lock Setting Memory LockDeactivating Memory Lock Recall the memory number to be Memory copyCopy source Press the + button to display the confirmation screen Press ButtonResetting to the default settings Initialization of currently selected memoryTo reset all parameters for all memory numbers Press Button to reset Parameters to their default SettingsSub monitor cable BNC cable for Component connection Connecting to AV componentsInput Signal type Connector type Pin/BNC Video cable Adapters Pin cableInput Signal type Connecting to computer devicesInformation for installers For US model onlyMounting the projector on a table Setting up the DPX-1200Mounting the projector on the ceiling When using a 43 screen When using a 169 screenProjection distance Using V.POS vertical position to adjust image position Keystone adjustmentUsing Zoom to adjust image position Using the adjusters to adjust image positionGlossary Vista size Test patternTracking Pulldown detection style IP conversionSignal type Active Pixels Lines KHz Compatible signal typesSignal type Active Fsc Color system Lines MHz Signal type Active Component type Pixels Lines KHzRegular care MaintenanceReplacing the filter Loosen the lamp cover screws Replacing the lampLamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningControls SpecificationsOptical GeneralDimensional drawing 119.1C2004 All Rights Reserved