Yamaha DPX-1200 manual Glossary

Page 57

11Reference

Glossary

The following is a list of key words used in the use of projectors and image signals and their explanations. Please refer to it when using this manual.

For an explanation of vocabulary used in the menu, refer to "Menu group items and functions” ( ☞ page 25).

Ceiling mount bracket

Interlace

The mounting hardware used to hang this unit from the ceiling.

The most common type of scanning used in televisions. It divides a

Two types of bracket are available, for high and low ceilings.

screen into even and odd numbered fields for scanning, and then

Ceiling mount brackets are sold separately.

builds an image by combining them into one image (frame).

Cinemascope size

The widest film format in 70 mm film, with an aspect of 2.35:1.

Color spacing

The conversion of YUV color separated signal to RGB signal. There are two formats for this, BT.601 for SDTV, and BT.709 for HDTV. This unit switches between them as required.

Component video signal

A method of sending video signals with independent luminance and color signals. Component video gives a higher image quality than ordinary composite video because it bypasses mixing and separating circuits. Component video signal consists of three lines, the luminance signal (Y), and two color difference signals (PB/CB, PR/CR).

Keystone Correction

Using the unit at an angle to the screen distorts the projected image trapezoidally. You can use Keystone Correction to electronically correct this distortion.

Letterbox

A method of converting the content of landscape oriented film to a 4:3 signal. You can watch landscape images without trimming them by adding a black bar to the top and bottom of the screen, however this sacrifices vertical resolution to some extent.

Progressive

A method of displaying all scanning lines in a frame at once, reducing flicker noticeable on a larger screen and creating a sharp, smooth image. This unit uses progressive scanning for progression.

Composite video signal

The most common type of video signal, combining luminance and color signals in one line. This method requires mixing and separating processes on both the send and receive sides. Use a pin cable for connection.

DCDiTM function

Directional Correlational Deinterlacing, a high quality image circuitry developed by the Faroudja company. DCDiTM uses edge cutting techniques to remove jagged edges from images during Interlace to Progressive conversion, allowing smooth, natural reproduction of images.

DLPTM technology

Digital Light Processing, an image display engine used in projectors that use the DMD™ chip developed by Texas Instruments.

D terminal

A cable that allows transmission of all of the signals in composite video in one cable. This method is used for transmitting image signals between the latest AV components. There are 5 methods of transmission, D1-D5. This unit is compatible with D4.

HDCP

A technique designed to protect the video transmission between a DVI or HDMI transmitter and a display device.

HDMITM

High-Definition Multimedia Interface, a method of differentially transmitting digital RGB/component video signal from computers and home digital equipment.

RGB Signal

A method of transmitting color information using a numeric representation of the primary colors red, green, and blue separately. When received, it is expressed in various colors by adding a mixing colors. RGB is widely used for sending and receiving color images between computers, and requires horizontal and vertical sync signals.

SDTV

Standard Definition Television, a term used to define normal television broadcasts which do not meet HDTV standards.

Smart zoom

Expands the left and right sides of a 4:3 image without altering the center, when you are attempting to project a 4:3 image on a wide screen format. This creates some distortion at both edges.

Squeeze

A method of compressing film images horizontally to an aspect of ratio of 4:3 when recording to video medium. The raw image is oblong, so needs to be passed through a desqueezing circuit to be projected in it’s original form.

Standby

The state in which the circuit that receives infrared-signals from the remote control is active, but all other main circuits are turned on. The unit consumes a small amount of power in this state.

S Video signal

S stands for Separate. A method of sending signals with separate luminance (Y) and color (C) signals. Use a 4-pin mini DIN connector and cable for connection.

11

Reference

HDTV

Sync.

High-Definition Television, a term used to define systems that

Computers output signals with a given regular frequency, which

satisfy the following conditions:

you must synchronize the projector to in order to produce a good

• A vertical resolution of 720p or 1080i (p stands for progressive

quality image. If you do not match the phase of the signal, the

scans, ; stands for interlace scans)

image may be flickery, faded, or distorted.

• A 16:9 aspect ratio

 

53

Page 56 Page 58
Image 57
Page 56 Page 58
Contents DPX-1200 Alleen voor klanten in Nederland Important Safety InstructionsFCC Information for US customers only We Want You Listening For a LifetimeIii Table of contents Accessory check Inappropriate places for installationFeatures Main unit Front panel and controls Main unit Rear panel / Connections Remote control functions Remote control code switch Light switchRemote control cable jack Hide buttonUsing the remote control with a wired connection Loading the batteries into the remote controlLimits for using the remote control Distance to sensor Angle to sensorUse within a left/right arc of 30 degrees Preparation If you have not installed the main unit or screenPrepararion Pre-operation check Checking installation and connectionsProjection preparations complete Main unitTurning the power on Turning the projector power onLamp may blink when half lit. This is not a defect Placing the DPX-1200 in standby modeMemo Press the STANDBY/ON buttonSelecting an input signal Selecting using the Input buttonProjection image signal Press the + button to open the submenu Using the Input button to select a signalButton Aspect Input buttonPress the Aspect button Selecting a display aspect for a projection imageRemote cotrol ButtonDisplay aspect types Representative examples Input signal typeInput imageDisplay aspectProjected imageAdjusting the vertical position V.POS button Adjusting the imagePattern button Crosshatch pattern Grayscale pattern Color bar patternZoom Menu screen Menu configurationsAdvanced Mode Basic ModeMenu items Menu item listLower level menu items Submenu ItemsMenu group items and functions Saturation HueColor Temp White CorrectionLevel Adjustment Color AdjustmentWhite Peaking IrisSignal Sync Adjustment Setup Level HdtvSignal Status TrackingInitial Setup Remote Control Reset button Remote control onlyMenu operations Operation button functionsPress the Menu button to open Menu operations 1 with no submenuPress the + or button to select a menu group Menu ButtonSetting method depends on the item selected Press the + or button to select a suitable settingRemote Control Main Unit Menu Button Remote Control Main UnitPress the h or g button to to adjust item settings Menu operations 2 with submenusPress the + button to move to Submenu See page 27 for datails about each color item Special menu operationsResetting the selected parameter Resetting all parametersChanging the position of the menu screen Subtitle Zoom Resetting the lamp running timePress the button Changing the GammaExample Using the inline menu Adjusting image quality using the inline menuInline menu composition Inline menu item listSaving memory settings Memory configurationsUsing the remote control Using the menuPress the g button to select Settings in the selected memoryBottom of the screen Press the h or g button to select Memory numberSetting Memory Lock Memory lockDeactivating Memory Lock Memory copy Recall the memory number to beCopy source Press Button Press the + button to display the confirmation screenInitialization of currently selected memory Resetting to the default settingsPress Button to reset Parameters to their default Settings To reset all parameters for all memory numbersInput Signal type Connector type Connecting to AV componentsSub monitor cable BNC cable for Component connection Pin/BNC Video cable Adapters Pin cableInformation for installers Connecting to computer devicesInput Signal type For US model onlySetting up the DPX-1200 Mounting the projector on a tableMounting the projector on the ceiling When using a 169 screen When using a 43 screenProjection distance Using Zoom to adjust image position Keystone adjustmentUsing V.POS vertical position to adjust image position Using the adjusters to adjust image positionGlossary Tracking Test patternVista size Pulldown detection style IP conversionSignal type Active Fsc Color system Lines MHz Compatible signal typesSignal type Active Pixels Lines KHz Signal type Active Component type Pixels Lines KHzMaintenance Regular careReplacing the filter Replacing the lamp Loosen the lamp cover screwsLamp cover screws To protect the lamp, you cannot turn on TroubleshootingTroubleshooting Message Condition Message displayLED indicator State Meaning LED indicator meaningsOptical SpecificationsControls General119.1 Dimensional drawingC2004 All Rights Reserved
Top Page Image Contents