Brother HL-660 manual Canadian Department of Communications Compliance Statement

Page 10

English

REGULATIONS

Canadian Department of Communications Compliance Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Department of Communications.

IMPORTANT (For U.K. only)

If the power cord supplied with this printer is not suitable for your electrical outlet, remove the plug from the mains cord and fit an appropriate three pin plug. If the replacement plug is intended to take a fuse then fit the same fuse as the original.

If a moulded plug is severed from the power cord then it should be destroyed because a plug with cut wires is dangerous if plugged into a live socket outlet. Do not leave it where a child might find it.

In the event of replacing the plug fuse, fit a fuse approved by ASTA to BS1362 with the same rating as the orginal fuse.

Always replace the fuse cover. Never use a plug with the cover omitted.

WARNING - THIS PRINTER MUST BE PROPERLY EARTHED.

The wires in the mains cord are coloured in accordance with the following code:

Green and yellow : Ground

Blue :Neutral

Brown :Live

The colours of the wiring in the power lead of this printer may not correspond with the markings which identify the terminals in your plug. If you need to fit a different plug, proceed as follows.

Remove a length of the cord outer sheath, taking care not to damage the coloured insulation of the wires inside.

Cut each of the three wires to the appropriate length. If the construction of the plug permits, leave the green and yellow wire longer than the others so that, in the event that the cord is pulled out of the plug, the green and yellow wire will be the last to disconnect.

Remove a short section of the coloured insulation to expose the wires.

The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter “E” or by the earth symbol or coloured green or green and yellow.

The wire which is coloured blue must be connected to the terminal which is marked with the letter “N” or coloured black or blue.

The wire which is coloured brown must be connected to the terminal which is marked with the letter “L” or coloured red or brown.

The outer sheath of the cord must be secured inside the plug. The coloured wires should not hang out of the plug.

ix

Page 9 Page 11
Image 10
Page 9 Page 11
Contents HL-660 Series Brother Laser PrinterShipment of the Printer Laser Printer HL-660 Series User’s Guide For USA & Canada OnlyTrademarks Compilation and Publication NoticeTable of Contents Options Regulations Laser Safety For 110-120 V Model OnlyRadio Interference For 220 240 V Model Only For Your Safety FDA RegulationsDisconnect device IEC 825 Laser Class For 220-240 V Model OnlyManufactured at Canadian Department of Communications Compliance Statement Important For U.K. onlyEnglish About the Guidebooks Learning How to Use the PrinterDefinitions of Warnings, Cautions, and Notes About Your Printer Printer OverviewFeatures Dpi Resolution and 6ppm Printing SpeedBi-Directional Parallel Interface APT Advanced Photoscale Technology Operating and Storage Environment Power SupplyEnvironment English Paper Specifications Chapter Paper HandlingFan the Paper Straighten the Paper Printable Area MULTI-PURPOSE Sheet Feeder Loading Paper into the Feeder Opening the Feeder Loading Paper or Envelope in the FeederMoving the Paper Guide Closing the Feeder Two Side Printing Manual Duplexing Manual Feed Slot Moving the Paper Guide Output Tray and Paper Support Wire Opening the Output Tray Extending the Paper Support WireLamps Ready LampData Lamp Alarm LampManual Lamp Select Reset Switch SwitchesSelect Switch FF/CONT Switch FF/CONTTEST SwitchReset Switch Test SwitchSleep Mode Reprint FunctionTest Print Mode DataReset/Hex Dump Mode Protection APT Advanced Photoscale TechnologyChapter Options BR-SCRIPT 2 ROM BoardAppletalk Interface Board Additional Memory Minimum Memory Recommendation including resident memoryEnglish Installing the Simm Unplug the power cord Disconnect the interface cableInstall the Simm Chapter Maintenance Replacing the Toner CartridgeRemoving the Multi-Purpose Sheet Feeder Remove the old toner cartridge from the printer Installing the Toner Cartridge Into the Drum Unit Replacing the Drum Unit Removing the Toner CartridgeInside the printer Remove the protective parts ① ⑥ in order as shown below 13 Installing the Drum Unit Adjusting the Print Density 14 Adjusting the Print Density DialCleaning the Printer Cleaning the Printer ExteriorCleaning the Printer Interior and Drum Unit 15 Inside the printer17 Cleaning the Printer Interior 18 Cleaning the Primary Corona Wire 19 Removing the Drum Unit Assembly RE-PACKING the Printer21 Repacking the Printer English Alarm Indications AT a Glance Operator CallsEnglish Service Calls Paper Jams Locating Paper Jam PositionPaper Jam in the Feeder Paper Jam Inside the Printer Setting up the Printer Hardware Setting up the Printer for DOSSetting up the Printer for Windows Setting up the Printer for Apple Macintosh Computers Paper Handling RecommendationsPrinting Print Quality White Stripes or Faint ImagesDark Stripes or Toner Stains 11 Scattering Toner 13 Stained at Fixed Interval English Printer Specifications AppendicesFunctions Electrical and MechanicalParallel Interface Specification Fig. A-1 Parallel interface cable Scalable Fonts Resident FontsBitmapped Fonts Intellifont Compatible FontsAppendix-6 HP LaserJet 4 Mode Symbol SETS/ Character SetsOCR Symbol Sets Epson ModeHP LaserJet HP LaserJet 4, Epson FX-850, IBM Propritner XL Appendix-10 Index Simm III UL5580001
Top Page Image Contents