Brother HL-660 manual Installing the Simm, Unplug the power cord Disconnect the interface cable

Page 41

English

CHAPTER 4 OPTIONS

Installing the SIMM

When you install the SIMM, follow these steps:

1Unplug the power cord from the AC outlet and disconnect the interface cable from the printer.

Fig. 4-3 Unplug the power cord and

Disconnect the interface cable

✒Note

Be sure to unplug the power cord to the printer before installing or removing the SIMM and the main controller board.

2Unscrew the three screws securing the rear plate of the main controller board and pull out the main controller board.

Fig. 4-4 Remove the main controller board

4–5

Image 41

Contents Brother Laser Printer HL-660 SeriesShipment of the Printer For USA & Canada Only Laser Printer HL-660 Series User’s GuideCompilation and Publication Notice TrademarksTable of Contents Options Radio Interference For 220 240 V Model Only Laser Safety For 110-120 V Model OnlyRegulations FDA Regulations For Your SafetyManufactured at IEC 825 Laser Class For 220-240 V Model OnlyDisconnect device Important For U.K. only Canadian Department of Communications Compliance StatementEnglish Definitions of Warnings, Cautions, and Notes Learning How to Use the PrinterAbout the Guidebooks Printer Overview About Your PrinterDpi Resolution and 6ppm Printing Speed FeaturesBi-Directional Parallel Interface APT Advanced Photoscale Technology Environment Power SupplyOperating and Storage Environment English Chapter Paper Handling Paper SpecificationsFan the Paper Straighten the Paper Printable Area MULTI-PURPOSE Sheet Feeder Opening the Feeder Loading Paper or Envelope in the Feeder Loading Paper into the FeederMoving the Paper Guide Closing the Feeder Two Side Printing Manual Duplexing Manual Feed Slot Moving the Paper Guide Opening the Output Tray Extending the Paper Support Wire Output Tray and Paper Support WireReady Lamp LampsManual Lamp Alarm LampData Lamp Select Switch SwitchesSelect Reset Switch Reset Switch FF/CONTTEST SwitchFF/CONT Switch Test SwitchReprint Function Sleep ModeData Test Print ModeReset/Hex Dump Mode APT Advanced Photoscale Technology ProtectionBR-SCRIPT 2 ROM Board Chapter OptionsAppletalk Interface Board Minimum Memory Recommendation including resident memory Additional MemoryEnglish Unplug the power cord Disconnect the interface cable Installing the SimmInstall the Simm Replacing the Toner Cartridge Chapter MaintenanceRemoving the Multi-Purpose Sheet Feeder Remove the old toner cartridge from the printer Installing the Toner Cartridge Into the Drum Unit Removing the Toner Cartridge Replacing the Drum UnitInside the printer Remove the protective parts ① ⑥ in order as shown below 13 Installing the Drum Unit 14 Adjusting the Print Density Dial Adjusting the Print DensityCleaning the Printer Exterior Cleaning the Printer15 Inside the printer Cleaning the Printer Interior and Drum Unit17 Cleaning the Printer Interior 18 Cleaning the Primary Corona Wire RE-PACKING the Printer 19 Removing the Drum Unit Assembly21 Repacking the Printer English Operator Calls Alarm Indications AT a GlanceEnglish Service Calls Locating Paper Jam Position Paper JamsPaper Jam in the Feeder Paper Jam Inside the Printer Setting up the Printer for DOS Setting up the Printer HardwareSetting up the Printer for Windows Setting up the Printer for Apple Macintosh Computers Recommendations Paper HandlingPrinting White Stripes or Faint Images Print QualityDark Stripes or Toner Stains 11 Scattering Toner 13 Stained at Fixed Interval English Appendices Printer SpecificationsElectrical and Mechanical FunctionsParallel Interface Specification Fig. A-1 Parallel interface cable Bitmapped Fonts Resident FontsScalable Fonts Intellifont Compatible FontsAppendix-6 OCR Symbol Sets Symbol SETS/ Character SetsHP LaserJet 4 Mode Epson ModeHP LaserJet HP LaserJet 4, Epson FX-850, IBM Propritner XL Appendix-10 Index Simm III UL5580001