Brother HL-660 manual Reprint Function, Sleep Mode

Page 33

English

CHAPTER 3 CONTROL PANEL

OTHER CONTROL FEATURES

The printer has the following useful features:

Reprint Function

You can use the FF/CONT switch as a Reprint switch, so you can reprint the last printed page without sending it again from your computer.

After you have finished printing, press the SELECT switch to turn the printer off-line and press the FF/CONT switch. The printer starts reprinting the last printed page. If you press the FF/CONT switch one or more times during reprinting, the printer reprints the page as many times as you pressed the switch.

✒Note

∙The reprint data remains in the printer’s memory until the printer is reset, the emulation is changed, or some other settings are changed. After you have printed confidential data, be sure to reset the printer to clear it from the printer’s memory.

∙You can enable or disable this reprint function with the supplied Remote Printer Console program. See the software setup guide for more information about RPC.

Sleep Mode

Whether the printer is in the on-line or off-line state and the printer does not receive data for a certain period of time (time out), it enters sleep mode. Sleep mode acts as though the printer has been turned off. The factory set default time out is 15 or 2 minutes. (The default value varies depending on the area.) While the printer is in sleep mode, all the lamps are off, however the printer can still receive data from the computer. Receiving a print file or document automatically awakens the printer to start printing. Pressing any switch also awakens the printer.

✒Note

∙This printer has no power switch. The sleep mode handles the power control.

∙When the printer goes into sleep mode, the fan will not stop until the printer engine has cooled down.

∙Sleep mode allows the print engine to cool, so the temperature of your room and how long the printer has been in sleep mode affects the warm-up time. This warm-up time can take from 5 seconds to 60 seconds. The READY lamp blinks to indicate that the printer is warming up.

∙You can change the time out for the sleep mode with the supplied printer driver and Remote Printer Console program. See the Software setup guide for more information about drivers.

3–5

Image 33

Contents Brother Laser Printer HL-660 SeriesShipment of the Printer For USA & Canada Only Laser Printer HL-660 Series User’s GuideCompilation and Publication Notice TrademarksTable of Contents Options Laser Safety For 110-120 V Model Only RegulationsRadio Interference For 220 240 V Model Only FDA Regulations For Your SafetyIEC 825 Laser Class For 220-240 V Model Only Disconnect deviceManufactured at Important For U.K. only Canadian Department of Communications Compliance StatementEnglish Learning How to Use the Printer About the GuidebooksDefinitions of Warnings, Cautions, and Notes Printer Overview About Your PrinterDpi Resolution and 6ppm Printing Speed FeaturesBi-Directional Parallel Interface APT Advanced Photoscale Technology Power Supply Operating and Storage EnvironmentEnvironment English Chapter Paper Handling Paper SpecificationsFan the Paper Straighten the Paper Printable Area MULTI-PURPOSE Sheet Feeder Opening the Feeder Loading Paper or Envelope in the Feeder Loading Paper into the FeederMoving the Paper Guide Closing the Feeder Two Side Printing Manual Duplexing Manual Feed Slot Moving the Paper Guide Opening the Output Tray Extending the Paper Support Wire Output Tray and Paper Support WireReady Lamp LampsAlarm Lamp Data LampManual Lamp Switches Select Reset SwitchSelect Switch Reset Switch FF/CONTTEST SwitchFF/CONT Switch Test SwitchReprint Function Sleep ModeData Test Print ModeReset/Hex Dump Mode APT Advanced Photoscale Technology ProtectionBR-SCRIPT 2 ROM Board Chapter OptionsAppletalk Interface Board Minimum Memory Recommendation including resident memory Additional MemoryEnglish Unplug the power cord Disconnect the interface cable Installing the SimmInstall the Simm Replacing the Toner Cartridge Chapter MaintenanceRemoving the Multi-Purpose Sheet Feeder Remove the old toner cartridge from the printer Installing the Toner Cartridge Into the Drum Unit Removing the Toner Cartridge Replacing the Drum UnitInside the printer Remove the protective parts ① ⑥ in order as shown below 13 Installing the Drum Unit 14 Adjusting the Print Density Dial Adjusting the Print DensityCleaning the Printer Exterior Cleaning the Printer15 Inside the printer Cleaning the Printer Interior and Drum Unit17 Cleaning the Printer Interior 18 Cleaning the Primary Corona Wire RE-PACKING the Printer 19 Removing the Drum Unit Assembly21 Repacking the Printer English Operator Calls Alarm Indications AT a GlanceEnglish Service Calls Locating Paper Jam Position Paper JamsPaper Jam in the Feeder Paper Jam Inside the Printer Setting up the Printer for DOS Setting up the Printer HardwareSetting up the Printer for Windows Setting up the Printer for Apple Macintosh Computers Recommendations Paper HandlingPrinting White Stripes or Faint Images Print QualityDark Stripes or Toner Stains 11 Scattering Toner 13 Stained at Fixed Interval English Appendices Printer SpecificationsElectrical and Mechanical FunctionsParallel Interface Specification Fig. A-1 Parallel interface cable Bitmapped Fonts Resident FontsScalable Fonts Intellifont Compatible FontsAppendix-6 OCR Symbol Sets Symbol SETS/ Character SetsHP LaserJet 4 Mode Epson ModeHP LaserJet HP LaserJet 4, Epson FX-850, IBM Propritner XL Appendix-10 Index Simm III UL5580001